- 您現在的位置：買賣IC網 > PDF目錄385241 > CN8333EXF PCM Transceiver PDF資料下載
參數資料
| 型號： | CN8333EXF |
| 英文描述： | PCM Transceiver |
| 中文描述： | 收發器的PCM |
| 文件頁數： | 27/48頁 |
| 文件大?。?/td> | 434K |
| 代理商： | CN8333EXF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
CN8331/CN8332/CN8333
2.0 Functional Description
Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit
2.3 Receiver
100604B
Conexant
2-9
2.3 Receiver
This section describes in detail various blocks in the CN8331/CN8332/CN8333
receiver.
2.3.1 Receive Sensitivity
The receiver recovers data from the coaxial cable that is attenuated due to the
frequency-dependent characteristics of the cable. In addition, the receiver
compensates for the flat loss (across all frequencies) in the various electrical
components and the variation in transmitted signal power.
The CN833x device is able to recover data that has been attenuated by a
maximum of 900 feet of coax having characteristics and attenuation consistent
with
ANSI T1.102-1993
, Annex C, Figure C.2. This approximates the
characteristics of AT&T type 734/728 cable; almost the same attenuation
characteristic is achieved by one-half the length of AT&T type 735 cable.
2.3.2 AGC/VGA Block
The Variable Gain Amplifier (VGA) receives the AMI input signal from the
coaxial cable. The VGA supplies flat gain (independent of frequency) to make up
for various flat losses in the transmission channel and for loss at one-half the
symbol rate that cannot be made up by the equalizer. The VGA gain is controlled
by a feedback loop which senses the amplitude of the equalizer output, acting to
servo this amplitude for optimal slicing.
2.3.3 Receive Equalizer
The receive equalizer receives the differential signal from a VGA and acts to
boost the high frequency content of the signal to reduce inter-symbol interference
(ISI) to the point that correct decisions can be made by the slicer with a minimum
of jitter in the recovered data.
The REQH pin is provided to allow lower amounts of equalization (shorter
equivalent cable lengths) for cases where a square-shaped pulse (that does not
meet the DS3/STS-1 standards) is transmitted to the receiver. A square-shaped
input has a much larger high-frequency content and could have overshoots at the
EQ output high enough to cause bit errors. Setting REQH = 0 will lower the gain
and reduce the amount of overshoot.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料 |
PDF描述 |
|---|---|
| CN8394KTF | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| CN8398KBG | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| CN8398KPF | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| CN8471AKPF | Industrial Control IC |
| CN8472AKPF | Industrial Control IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CN8333EXF28333-15ES1 | 制造商:Conexant 功能描述: |
| CN8366-000 | 制造商:TE Connectivity 功能描述:44/0412-22-9CS1038 |
| CN8371-000 | 制造商:TE Connectivity 功能描述:RNF-100-3/8-WH-SP-CS5004 制造商:TE Connectivity 功能描述:RNF-100-3/8-WH-SP-CS5004 - Bulk |
| CN8373-000 | 制造商:TE Connectivity 功能描述:XFFR-30-04/97 - Bulk |
| CN8380 | 制造商:CONEXANT 制造商全稱:CONEXANT 功能描述:integrated quad line interface unit unit for both 1.544 Mbps (T1) and 2.048 Mbps (E1) applications |
發布緊急采購，3分鐘左右您將得到回復。