- 您現在的位置：買賣IC網 > PDF目錄385241 > CMX218 ISDN Data and Telephony-Protocol Engine??? PDF資料下載
參數資料
| 型號： | CMX218 |
| 英文描述： | ISDN Data and Telephony-Protocol Engine??? |
| 中文描述： | ISDN數據和語音通信協議引擎？？？ |
| 文件頁數： | 18/34頁 |
| 文件大?。?/td> | 353K |
| 代理商： | CMX218 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
ISDN Data and Telephony Protocol Engine (no X.25)
CMX218
1999
Consumer Microcircuits Limited
1999
Chiron Technology Limited
18
D/218/1
The escape sequence ‘+++’ (with Guard Time = 1s before and after the sequence) will cause the
CMX218 to enter the command state from the data state and to return on ‘OK’ response. Sending an
ATO command will be ignored, ie the CMX218 remains in the command state.
The following is a more detailed description of the Hayes commands listed above:
A (Answer)
Format:ATA<CR>
Causes the CMX218 to answer an incoming data call, by sending a CONNECT message to the
network. If a CONNECT ACK is received the CMX218 enters the data state after returning a
‘CONNECT XXX’ result code to the DTE on the RS232 port (where the XXX is the speed in baud). If
a RELEASE, RELEASE COMPLETE or DISCONNECT message is received a ‘NO CARRIER’ result
code is returned. The command is not valid if there is no incoming call and it will return ‘ERROR’.
D (Dial)
Format:ATD{DN}<CR>
Format:ATDT{DN}<CR>
Format:ATDP{DN}<CR>
{DN} is a directory number of up to 23 ASCII characters from 0..9,
S
and
#
. This form of the ATD
command causes an outgoing SETUP message to be sent to the network with a Called Party Number
Information Element which contains the digits included in the command. Any commands that follow
this command are ignored.
If the CMX218 receives any character from the DTE after an ATD command, which causes a SETUP
message to be sent to the network, and before the call is connected, the attempt to make a call is
abandoned, ie a DISCONNECT message will be sent to the network and a ‘NO CARRIER’ result code
returned.
Calls are established with the D command, irrespective of the state of the DTR pin. The result code
response is either:
'CONNECT'
'NO CARRIER'
'NO DIALTONE'
'BUSY'
- call successful. The CMX218 will automatically enter the data state.
- call rejected by the remote user or the network
- ISDN link down
- remote user busy and other causes
Calls are cleared in the following way:
(i) The remote end or network clears the call by sending a DISCONNECT message or the ISDN
line fails/is removed: 'NO CARRIER' is sent to DTE.
(ii) DTR is dropped (with a de-bounce period of 50ms) by DTE causing the CMX218 to send a
DISCONNECT message to the network and enter the disconnect state, awaiting a RELEASE
COMPLETE from the network. The CMX218 sends the 'OK' response when clearing of the ISDN
call is complete ie RELEASE and RELEASE COMPLETE messages have been transmitted
across the network, (dependant upon the state of &D command).
(iii) The DTE issues the escape sequence ‘+++ ‘(with Guard Time = 1s before and after the
sequence), receives an 'OK' response and then issues the Hang-up command (see section on H
command below). The CMX218 sends the 'OK' response when clearing of the ISDN call is
complete.
相關PDF資料 |
PDF描述 |
|---|---|
| CMX228 | ISDN Protocol Engine? D-Channel Data?? |
| CMXT2207 | BJT |
| CN305 | Optoelectronic |
| CN3801 | Analog IC |
| CN3802 | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CMX218S1 | 制造商:CMLMICRO 制造商全稱:CML Microcircuits 功能描述:ISDN Data/Telephony Protocol Engine |
| CMX228 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ISDN Protocol Engine? D-Channel Data?? |
| CMX228S1 | 制造商:CMLMICRO 制造商全稱:CML Microcircuits 功能描述:ISDN Protocol Engine with D - channel Data |
| CMX264 | 制造商:CMLMICRO 制造商全稱:CML Microcircuits 功能描述:Frequency Domain Split Band Scrambler |
| CMX309 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CLOCK OSCILLATORS |
發布緊急采購，3分鐘左右您將得到回復。