- 您現在的位置：買賣IC網 > PDF目錄3768 > CMS82C55AZ96 (Intersil)IC I/O EXPANDER 24B 44PLCC PDF資料下載
參數資料
| 型號： | CMS82C55AZ96 |
| 廠商： | Intersil |
| 文件頁數： | 6/26頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC I/O EXPANDER 24B 44PLCC |
| 標準包裝： | 500 |
| 接口： | 可編程 |
| 輸入/輸出數： | 24 |
| 中斷輸出： | 無 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 供應商設備封裝： | 44-PLCC |
| 包裝： | 帶卷 (TR) |
14
FN6140.2
June 15, 2006
Special Mode Combination Considerations
There are several combinations of modes possible. For any
combination, some or all of Port C lines are used for control
or status. The remaining bits are either inputs or outputs as
defined by a “Set Mode” command.
During a read of Port C, the state of all the Port C lines,
except the ACK and STB lines, will be placed on the data
bus. In place of the ACK and STB line states, flag status will
appear on the data bus in the PC2, PC4, and PC6 bit
positions as illustrated by Figure 17.
Through a “Write Port C” command, only the Port C pins
programmed as outputs in a Mode 0 group can be written.
No other pins can be affected by a “Write Port C” command,
nor can the interrupt enable flags be accessed. To write to
any Port C output programmed as an output in Mode 1
group or to change an interrupt enable flag, the “Set/Reset
Port C Bit” command must be used.
With a “Set/Reset Port C Bit” command, any Port C line
programmed as an output (including IBF and OBF) can be
written, or an interrupt enable flag can be either set or reset.
Port C lines programmed as inputs, including ACK and STB
lines, associated with Port C are not affected by a “Set/Reset
Port C Bit” command. Writing to the corresponding Port C bit
positions of the ACK and STB lines with the “Set Reset Port
C Bit” command will affect the Group A and Group B
interrupt enable flags, as illustrated in Figure 17.
Current Drive Capability
Any output on Port A, B or C can sink or source 2.5mA. This
feature allows the 82C55A to directly drive Darlington type
drivers and high-voltage displays that require such sink or
source current.
MODE DEFINITION SUMMARY
MODE 0
MODE 1
MODE 2
IN
OUT
IN
OUT
GROUP A ONLY
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
In
Out
In
Out
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
In
Out
In
Out
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
In
Out
INTRB
IBFB
STBB
INTRA
STBA
IBFA
I/O
INTRB
OBFB
ACKB
INTRA
I/O
ACKA
OBFA
I/O
INTRA
STBA
IBFA
ACKA
OBFA
Mode 0
or Mode 1
Only
INPUT CONFIGURATION
D7
D6
D5
D4
D3
D2
D1
D0
I/O
IBFA
INTEA INTRA INTEB
IBFB
INTRB
OUTPUT CONFIGURATION
D7
D6
D5
D4
D3
D2
D1
D0
OBFA INTEA
I/O
INTRA INTEB
OBFB INTRB
FIGURE 15. MODE 1 STATUS WORD FORMAT
D7
D6
D5
D4
D3
D2
D1
D0
OBFA
INTE1
IBFA
INTE2 INTRA
X
(Defined by Mode 0 or Mode 1 Selection)
FIGURE 16. MODE 2 STATUS WORD FORMAT
GROUP A
GROUP B
GROUP A
GROUP B
GROUP A
GROUP B
MS82C55A, MQ82C55A, MP82C55A
相關PDF資料 |
PDF描述 |
|---|---|
| CMS82C55AZ | IC I/O EXPANDER 24B 44PLCC |
| CS82C55A-5Z96 | IC I/O EXPANDER 24B 44PLCC |
| MCP2200-I/SO | IC USB TO UART 20SOIC |
| ATMEGA48-15MZ | MCU AVR 4K FLASH 15MHZ 32-QFN |
| CS82C55A-5Z | IC I/O EXPANDER 24B 44PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CMS8D | 制造商:SUMIDA 制造商全稱:Sumida Corporation 功能描述:Strobe Light Transformer |
| CMS8D57 | 制造商:SUMIDA 制造商全稱:Sumida Corporation 功能描述:Strobe Light Transformer |
| CMS8D75 | 制造商:SUMIDA 制造商全稱:Sumida Corporation 功能描述:Strobe Light Transformer |
| CMS-8GB60 | 制造商:AXIOM 功能描述:Tools Development kit Interfa 制造商:AXIOM 功能描述:MC9S08GB60, RS232, SPI, DEVELOPMENT BOARD, Silicon Manufacturer:Freescale, Core 制造商:AXIOM 功能描述:MC9S08GB60, RS232, SPI, DEVELOPMENT BOARD, Silicon Manufacturer:Freescale, Core Architecture:HC08, Core Sub-Architecture:HC08, Silicon Core Number:MC9S08GB60, Silicon Family Name:68HC08, Clock Frequency:32kHz, For Use With:M9S08GB60 , RoHS Compliant: No |
| CMS-9000-G729 10P | 制造商:RadiSys 功能描述:MX S6800 G.729 CODEC LIC W/SUPT Q10 - Bulk |
發布緊急采購，3分鐘左右您將得到回復。