- 您現在的位置：買賣IC網 > PDF目錄384222 > CM1481 Non-Predictive Selcall Module PDF資料下載
參數資料
| 型號： | CM1481 |
| 英文描述： | Non-Predictive Selcall Module |
| 中文描述： | 非預測Selcall模塊 |
| 文件頁數： | 4/24頁 |
| 文件大小： | 162K |
| 代理商： | CM1481 |
4
Installation
Regulator
Micro-Controller
Audio
Signalling
Processor
EEPROM
PTT IN
(5)
Tx CALL
(3)
QUIET/OPEN
(4)
Tx ON
(11)
V IN
(13)
(12)
GND
MUTE CTRL (10)
(8)
(9)
LED
TONE OUT
ALERT
(7)
BUSY
(2)
CONFIG
(1)
SIGNAL IN
(6)
Power Supply
Audio Switch
Fig.2 The Radio Interface
Method of Installation
Ensuring that there is sufficient room to introduce
the Radio Interface lead and the Configuration
Interface Connector, place the CM1481 into its
operating position using the double-sided sticky-pad
(supplied) on the discrete component side of the
module. Ensure that the module adheres firmly to its
mounting surface.
Consider the requirements for Single or Dual
Button operation.
Do not attempt to install the module into areas of
the radio where it may be subject to high RF fields.
Ensure that the CM1481 is well insulated from other
radio components.
It is recommended, at this stage, that some record
is formulated to identify the configuration state of the
module/radio pair.
Power Requirements
The supply voltage requirement of the CM1481 is
between 6 and 26 volts d.c.
Handling Precautions
The CM1481, which is supplied in an anti-static
package, contains CMOS devices. It is recommended
that to prevent damage, Electrostatic Discharge
Precautions are employed at all stages of any
production process involving this module.
Alert Audio Levels
If alert levels from the CM1481 are to be fed into
an external audio amplifier it is recommended that the
LINK is removed. Removal of the LINK will allow
connection to high-impedance loads.
LINK IN can drive an external loudspeaker.
LINK OUT can drive an external amplifier.
See layout diagrams, Figure 4, and Table 5 (Audio
Alert Descriptions).
Installation Dimensions
CM1481 board size.
45mm x 22mm x 8mm.
Installation Instructions
The CM1481 is designed to be embodied physically within a mobile, portable or handheld transceiver to interface
electrically with Rx and Tx audio circuitry via the Radio Interface. The diagram below shows the input and output
system functions of the CM1481.
Before Installation it is recommended that this document is studied carefully.
相關PDF資料 |
PDF描述 |
|---|---|
| CM150DY12E | TRANSISTOR | IGBT POWER MODULE | HALF BRIDGE | 600V V(BR)CES | 150A I(C) |
| CM150E3Y12E | TRANSISTOR | IGBT POWER MODULE | INDEPENDENT | 600V V(BR)CES | 150A I(C) |
| CM150E3Y24E | TRANSISTOR | IGBT POWER MODULE | INDEPENDENT | 1.2KV V(BR)CES | 150A I(C) |
| CM150DY24E | TRANSISTOR | IGBT POWER MODULE | HALF BRIDGE | 1.2KV V(BR)CES | 150A I(C) |
| CM200DU12H | TRANSISTOR | IGBT POWER MODULE | HALF BRIDGE | 600V V(BR)CES | 200A I(C) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CM1481-02DE | 功能描述:電磁干擾濾波器 2-ch Headset Speaker EMI Filter with ESD RoHS:否 制造商:STMicroelectronics 電容:12 pF 電路類型: 最大直流電流: 最大直流電阻: 電壓額定值:6 V 容差: 端接類型:SMD/SMT 工作溫度范圍:- 30 C to + 85 C 系列:EMIF03 |
| CM1482 | 制造商:CML 制造商全稱:Chicago Miniature Lamp,inc 功能描述:G-4 1/2 Miniature Bayonet Base |
| CM1482-02DE | 功能描述:電磁干擾濾波器 2-ch Headset Mic EMI Filter with ESD RoHS:否 制造商:STMicroelectronics 電容:12 pF 電路類型: 最大直流電流: 最大直流電阻: 電壓額定值:6 V 容差: 端接類型:SMD/SMT 工作溫度范圍:- 30 C to + 85 C 系列:EMIF03 |
| CM1483 | 制造商:CML 制造商全稱:Chicago Miniature Lamp,inc 功能描述:G-4 1/2 Miniature Bayonet Base |
| CM1483-02DE | 功能描述:電磁干擾濾波器 L-C EMI Filter with ESD Protection RoHS:否 制造商:STMicroelectronics 電容:12 pF 電路類型: 最大直流電流: 最大直流電阻: 電壓額定值:6 V 容差: 端接類型:SMD/SMT 工作溫度范圍:- 30 C to + 85 C 系列:EMIF03 |
發布緊急采購，3分鐘左右您將得到回復。