- 您現在的位置：買賣IC網 > PDF目錄384221 > CLP200 OVERVOLTAGE AND OVERCURRENT PROTECTION FOR TELECOM LINE - (ASD) PDF資料下載
參數資料
| 型號： | CLP200 |
| 英文描述： | OVERVOLTAGE AND OVERCURRENT PROTECTION FOR TELECOM LINE - (ASD) |
| 中文描述： | 過壓和過流保護的電信線路保護- （ASD）的 |
| 文件頁數： | 7/21頁 |
| 文件大?。?/td> | 360K |
| 代理商： | CLP200 |
CLP200M
7/21
Fig. 7a and 7b
R
SENSE
.
:
Switching-on current versus
0.01
0.1
1
10
10
100
1000
t (ms)
Ipp (A)
Fig. 9 :
Operation limits and destruction zone of
the CLP200M.
CLP200M
Rsense
Rsense
1
FAILURE
STATUS
+12V
1k
Fig. 8 :
Failure Status circuit and diagnostic.
3
5
7
9
11
13
100
200
300
500
Rsense ( )
ISWON (mA)
-20°C
25°C
75°C
3
5
Rsense ( )
7
9
11
100
200
300
500
Iswon @ 25°C (mA)
Iswon min
negative
Iswon max
negative
Iswon min
positive
Iswon min
positive
The choice of the switching-on current is function
of the R
SENSE
resistors.
In normal operating condition, only the negative
current of the signal is of interest. This current (typ-
ically below -150 mA) should not activate the pro-
tection device CLP200M. Therefore the level of
activation is to be chosen just above this limit (typi-
cally -200 mA). This level is adjusted through
R
SENSE
.
Figures 7a and 7b enable the designers to choose
the right R
SENSE
value.
EXAMPLE :
The choice of R
SENSE
= 4
ensures a negative
triggering of -220 mA min and -320 mA max. In this
case, the positive triggering will be 180mA min and
280 mA max.
2.5 . Failure Status
The CLP200M has an internal feature that allows
the user to get a Failure Status (FS) indication.
When the CLP200M is short-circuiting the line to
GND, a signal can be managed through pin 1. This
signal can be used to turn a LED on in order to pro-
vide a surge indication. It may also be used with a
logic circuitry to count the number of disturbances
appearing on the lines.
If a surge exceeding the maximum ratings of the
CLP200Moccursontheline,thedevicewillfailina
short-circuit state.
The figure 9 shows two different curves :
I
The
lower
one
guaranted working limits of the CLP200M.
I
The upper curve shows the limit above which the
CLP200Miscompletelydestructed. Inthiscase,
the Fail Diagnostic pin is on.
indicates
the
maximum
相關PDF資料 |
PDF描述 |
|---|---|
| CLP200M-TR | OVERVOLTAGE AND OVERCURRENT PROTECTION FOR TELECOM LINE - (ASD) |
| CLR2170 | PHOTOTRANSISTOR | DARLINGTON | 850NM PEAK WAVELENGTH | 200M | CAN-4.6 |
| CLR2169 | PHOTOTRANSISTOR | DARLINGTON | 780NM PEAK WAVELENGTH | 200M | CAN-4.6 |
| CLR2180 | PHOTOTRANSISTOR | DARLINGTON | 850NM PEAK WAVELENGTH | 200M | CAN-4.6 |
| CLR4180 | PHOTOTRANSISTOR | DARLINGTON | 780NM PEAK WAVELENGTH | 200M | LED-7B |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CLP200M | 功能描述:TVS二極管陣列 Telecom Protection RoHS:否 制造商:Littelfuse 極性: 通道:4 Channels 擊穿電壓: 鉗位電壓:11.5 V 工作電壓:2.5 V 峰值浪涌電流:20 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 系列: 最小工作溫度:- 40 C 最大工作溫度:+ 85 C |
| CLP200M_03 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:OVERVOLTAGE AND OVERCURRENT PROTECTION FOR TELECOM LINE |
| CLP200M-TR | 功能描述:TVS二極管陣列 Telecom Protection RoHS:否 制造商:Littelfuse 極性: 通道:4 Channels 擊穿電壓: 鉗位電壓:11.5 V 工作電壓:2.5 V 峰值浪涌電流:20 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 系列: 最小工作溫度:- 40 C 最大工作溫度:+ 85 C |
| CLP-201 | 功能描述:散熱片 STANDARD CLIP 14.99X13.59X3.18 RoHS:否 制造商:Ampro By ADLINK 產品:Heat Sink Accessories 安裝風格:Through Hole 散熱片材料: 散熱片樣式: 熱阻: 長度: 寬度: 高度: 設計目的:Express-HRR |
| CLP-202 | 制造商:Aavid Thermalloy 功能描述:MOUNTING CLIPS 制造商:Aavid Thermalloy 功能描述:- Bulk 制造商:Aavid Thermalloy 功能描述:Aavid Internal P/N:033123 |
發布緊急采購，3分鐘左右您將得到回復。