- 您現在的位置：買賣IC網 > PDF目錄379896 > CLC428 (National Semiconductor Corporation) Dual Wideband, Low-Noise, Voltage Feedback Op Amp PDF資料下載
參數資料
| 型號： | CLC428 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Dual Wideband, Low-Noise, Voltage Feedback Op Amp |
| 中文描述： | 雙寬帶，低噪聲，電壓反饋運算放大器 |
| 文件頁數： | 4/8頁 |
| 文件大?。?/td> | 898K |
| 代理商： | CLC428 |
Application Discussion
Low Noise Design
Ultimate low noise performance from circuit designs using
the CLC428 requires the proper selection of
external resistors. By selecting appropriate low-valued
resistors for R
f
and R
g
, amplifier circuits using the CLC428
can achieve output noise that is approximately the
equivalent voltage input noise of 2.0 nV/
√
Hz multiplied
by the desired gain (Av).
Each amplifier in the CLC428 has an equivalent
input noise resistance which is optimum for matching
source impedances of approximately 1k. Using a
transformer, any source can be matched to achieve the
lowest noise design.
For even lower noise performance than the CLC428,
consider the CLC425 or CLC426 at 1.05 and 1.6 nV/
√
Hz,
respectively.
DC Bias Currents and Offset Voltages
Cancellation of the output offset voltage due to input bias
currents is possible with the CLC428. This is done by
making the resistance seen from the inverting and non-
inverting inputs equal. Once done, the residual output
offset voltage will be the input offset voltage (Vos) multi-
plied by the desired gain (Av). Comlinear Application Note
OA-7 offers several solutions to further reduce the output
offset.
Output and Supply Considerations
With ±5V supplies, the CLC428 is capable of a typical
output swing of ±3.8V under a no-load condition.
Additional output swing is possible with slightly higher
supply voltages. For loads of less than 50
, the output
swing will be limited by the CLC428’s output current
capability, typically 80mA.
Output settling time when driving capacitive loads can be
improved by the use of a series output resistor. See the
plot labeled "Settling Time vs. Capacitive Load" in the
Typical Performance section.
Layout
Proper power supply bypassing s critical to nsure good high
frequency performance and low noise. De-coupling capaci-
tors of 0.1
μ
F should be place as close as possible to the
power supply pins. The use of surface mounted capacitors
is recommended due to their low series inductance.
A good high frequency layout will keep power supply and
ground traces away from the inverting input and output
pins. Parasitic capacitance from these nodes to ground
causes frequency response peaking and possible circuit
oscillation. See OA-15 for more information. National
suggests the CLC730038 (through-hole) or the CLC730036
(SOIC) dual op amp evaluation board as a guide for high
frequency layout and as an aid in device evaluation.
http://www.national.com
4
相關PDF資料 |
PDF描述 |
|---|---|
| CLC428AJE | Dual Wideband, Low-Noise, Voltage Feedback Op Amp |
| CLC430 | General Purpose 100MHz Op Amp with Disable |
| CLC431 | Dual Wideband Monolithic Op Amp with Disable |
| CLC432 | Dual Wideband Monolithic Op Amp with Disable |
| CLC436AJP | IC-FEEDBACK OP-AMP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CLC428 DIE | 制造商:Texas Instruments 功能描述: |
| CLC428 WAF | 制造商:Texas Instruments 功能描述: |
| CLC428/CLC5802M WAF | 制造商:Texas Instruments 功能描述: |
| CLC428A | 制造商:ROCHESTER 制造商全稱:ROCHESTER 功能描述:VERSATILE, HIGH SPEED OP AMP perfect for a variety of applications Operational Amplifier |
| CLC428A/BPA | 制造商:Rochester Electronics LLC 功能描述: |
發(fā)布緊急采購，3分鐘左右您將得到回復。