- 您現在的位置：買賣IC網 > PDF目錄379870 > CE6353 (Intel Corp.) Nordig Unified DVB-T COFDM Terrestrial Demodulator for PC-TV and Hand-held Digital TV (DTV) PDF資料下載
參數資料
| 型號： | CE6353 |
| 廠商： | Intel Corp. |
| 英文描述： | Nordig Unified DVB-T COFDM Terrestrial Demodulator for PC-TV and Hand-held Digital TV (DTV) |
| 中文描述： | NorDig統一的DVB - T的COFDM地面解調器為PC - TV和手持式數字電視（DTV） |
| 文件頁數： | 25/26頁 |
| 文件大?。?/td> | 322K |
| 代理商： | CE6353 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁
CE6353
Data Sheet
25
Intel Corporation
4.4.1.5 Oscillator/Clock Application Notes
On the printed circuit board, the tracks to the crystal and capacitors must be made as short as possible.
Other signal tracks must not be allowed to cross through this area. The component tracks should preferably
be ringed by a ground track connected to the chip ground (0 V) on adjacent pins either side of the crystal
pins. It is also advisable to provide a ground plane for the circuit to reduce noise.
External clock signals, applied to XTI and/or XTO, must not exceed the cell supply limits (i.e., 0V and CVDD)
and current into or out of XTI and/or XTO must be limited to less than 10mA to avoid damaging the cell’s
amplitude clamping circuit.
An external, DC coupled, single ended square wave clock signal may be applied to XTI if OSCMODE = 0. To
limit the current taken from the signal source a resistor should be placed between the clock source and XTI.
The recommended value for this series resistor is 470
Ω
for a clock signal switching between 0 V and
CVDD. The current the clock source needs to source/sink is then <1.9 mA. The XTO pin must be left
unconnected in this configuration.
AC coupling of a single ended external clock to XTI, with OSCMODE = 0, is not recommended. The duty
cycle of the OSCOUT signal cannot be guaranteed in such a configuration.
AC coupling of a single ended external clock to XTI, with OSCMODE = 1, is possible. It is recommended that
the circuit shown in Figure 11 be used to correctly bias the oscillator inputs: The common-mode voltage VCM
for XTI and XTO, (set by the 36 k
Ω
and 22 k
Ω
resistors) must be 800 mV < VCM < CVDD and the amplitude
Vpp of the clock signal must be >100 mV.
Figure 11 - External Clocking via AC Coupling
External, differential clock signals may be applied to XTI and XTO if OSCMODE = 1. The common-mode
voltage VCM for the differential clock signals must be 800 mV < VCM < CVDD, and the peak-to-peak signal
amplitude Vpp must be >100 mV. It is recommended that differential clock signals have VCM = 1.0V. For
Vpp > 400 mV a resistor of >390
Ω
in series with XTI or XTO may be required to limit the current taken from
or supplied to the clock sources.
External clock
10nF
XTI
100k
10nF
22k
36k
XTO
Vdd
OSCMODE
相關PDF資料 |
PDF描述 |
|---|---|
| CE66P1 | 0.35um CMOS Technology |
| CE66P2 | 0.35um CMOS Technology |
| CE66P3 | 0.35um CMOS Technology |
| CE66P4 | 0.35um CMOS Technology |
| CE66P5 | 0.35um CMOS Technology |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CE645W5H56VJIBF | 制造商: 功能描述: 制造商:undefined 功能描述: |
| CE64MGMVA-F1050-D | 制造商:Delkin Devices 功能描述:64GB CF, SLC NAND, -40 TO 85C OPERATING TEMP, LOCKED BOM, MA - Bulk |
| CE66 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:0.35um CMOS Technology |
| CE66.5100.151 | 功能描述:交流電源輸入模塊 CE PWR ENTRY MODULE W. FILTER 10A RoHS:否 制造商:Schurter 過濾:Yes 過濾器類型:IEC Inlet Filters 產品:Inlets 電流額定值:4 A 電壓額定值:250 VAC 外殼材料:Thermoplastic 安裝風格:Panel, Screw 端接類型:Quick Connect 工作溫度范圍:- 25 C to + 85 C 連接器類型:C-14 |
| CE66P1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:0.35um CMOS Technology |
發布緊急采購，3分鐘左右您將得到回復。