- 您現在的位置：買賣IC網 > PDF目錄379858 > CDP68HC68W1 (Intersil Corporation) CONNECTOR ACCESSORY PDF資料下載
參數資料
| 型號： | CDP68HC68W1 |
| 廠商： | Intersil Corporation |
| 英文描述： | CONNECTOR ACCESSORY |
| 中文描述： | 連接器附件 |
| 文件頁數： | 9/24頁 |
| 文件大小： | 139K |
| 代理商： | CDP68HC68W1 |
9
CLK OUT
Clock output pin. One of seven frequencies can be selected
(or this output can be set low) by the levels of the three
LSB’s in the Clock-Control Register. If a frequency is
selected, it will toggle with a 50% duty cycle except 2Hz in
the 50Hz time base mode. (Ex, if 1Hz is selected, the output
will be high for 500ms and low for the same period). During
power-down operation (bit 6 in Interrupt Control Register set
to “1”), the clock-output pin will be set low.
CPUR
CPU reset output pin. This pin functions as an N-Channel
only, open-drain output and requires an external pull-up
resistor.
INT
Interrupt output pin. This output is driven from a single NFET
pulldown transistor and must be tied to an external pull-up
resistor. The output is activated to a low level when:
1. Power-sense operation is selected (B5 = 1 in Interrupt
Control Register) and a power failure occurs.
2. A previously set alarm time occurs. The alarm bit in the
Status Register and interrupt-out signal are delayed
30.5
μ
s when 32kHz operation is selected and 15.3
μ
s for
2MHz and 7.6
μ
s for 4MHz.
3. A previously selected periodic interrupt signal activates.
The Status Register must be read to set the Interrupt output
high after the selected periodic interval occurs. This is also
true when conditions 1 and 2 activate the interrupt. If power
down had been previously selected, the interrupt will also
reset the power-down functions.
SCK, MOSI, MISO
See Serial Peripheral Interface (SPI) section in this data sheet.
CE
A positive chip-enable input. A low level at this input holds the
serial interface logic in a reset state. This pin is also used for
the watchdog function.
V
SS
The negative power-supply pin that is connected to ground.
PSE
Power-supply enable output pin. This pin is used to control
power to the system. The pin is set high when:
1. V
SYS
rises above the V
BATT
voltage after V
SYS
was
placed low by a system failure.
2. An interrupt occurs.
3. A power-on reset (if V
SYS
is a logic high).
The PSE pin is set low by writing a high into bit 6 (power-
down bit) in the Interrupt Control Register.
POR
Power-on reset. A Schmitt-trigger input that generates a
power-on internal reset signal using an external R-C net-
work. Both control registers and frequency dividers for the
oscillator and line input are reset. The Status Register is
reset except for the first time up bit (B4), which is set.
Single supply or battery backup operation is selected at the
end of POR.
LINE
This input is used for two functions. When not used it
should be connected to V
DD
via a 10k
resistor. The first
function utilizes the input signal as the frequency source for
the timekeeping counters. This function is selected by
setting bit 6 in the Clock Control Register. The second
function enables the line input to sense a power failure.
Threshold detectors operating above and below V
DD
sense
an AC voltage loss. Bit 5 must be set to “1” in the Interrupt
Control Register and crystal or external clock source
operation is required. Bit 6 in the Clock Control Register
must be low to select XTAL operation.
Oscillator Circuit
The CDP68HC68T1 has an on-board 150K resistor that is
switched in series with its internal inverter when 32kHz is
selected via the Clock Control Register. Note: When first
powered up the series resistor is not part of the oscillator
circuit. (The CDP68HC68T1 sets up for a 4MHz oscillator).
MISO
V
BATT
REAL-TIME CLOCK
CDP68HC68T1
PSE
CPUR
CLK
OUT
SERIAL
INTERFACE
V
SYS
MOSI
FIGURE 6. POWER-UP FUNCTIONAL DIAGRAM (INITIATED BY
A RISE IN VOLTAGE ON THE “V
SYS
” PIN)
CDP68HC68T1
相關PDF資料 |
PDF描述 |
|---|---|
| CDP68HC68W1E | CONNECTOR ACCESSORY |
| CDP68HC68A2 | CMOS Serial 10-Bit A/D Converter |
| CDP68HC68A2E | CMOS Serial 10-Bit A/D Converter |
| CDP68HC68A2M | CMOS Serial 10-Bit A/D Converter |
| CDP68HC68P1 | CMOS Serial 8-Bit Input/Output Port |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CDP68HC68W1E | 制造商:Harris Corporation 功能描述: |
| CDP68HCL05C16BD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| CDP68HCL05C16BE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| CDP68HCL05C16BN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| CDP68HCL05C16BQ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。