參數資料
型號： CDB4398
廠商： Cirrus Logic Inc
文件頁數： 13/46頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR CS4398 DAC
標準包裝： 1
DAC 的數量： 2
位數： 24
采樣率（每秒）： 192k
數據接口： I²C，SPI?
DAC 型： 電壓
工作溫度： -10°C ~ 70°C
已供物品： 板，線纜
已用 IC / 零件： CS4398
產品目錄頁面： 757 (CN2011-ZH PDF)
相關產品： 598-1067-5-ND - IC DAC 120DB 192KHZ W/VC 28TSSOP
其它名稱： 598-1155
20
DS568F1
CS4398
4. APPLICATIONS
4.1
Grounding and Power Supply Decoupling
As with any high resolution converter, the CS4398 requires careful attention to power supply and grounding
arrangements to optimize performance. The Typical Connection Diagram shows the recommended power
arrangement with VA, VD, VLS and VLC connected to clean supplies. Decoupling capacitors should be lo-
cated as close to the device package as possible. If desired, all supply pins may be connected to the same
supply, but the recommended decoupling capacitors should still be placed on each supply pin. The AGND
and DGND pins should be tied together with solid ground plane fill underneath the converter extending out
to the GND side of the decoupling caps for VA, VD, VREF, and FILT+. This recommended layout can be
seen in the CDB4398 evaluation board and datasheet.
4.2
Analog Output and Filtering
The Cirrus Logic application note “Design Notes for a 2-Pole Filter with Differential Input” (AN48) discusses
the second-order Butterworth filter and differential to single-ended converter topology that was implemented
on the CS4398 evaluation board, CDB4398, as seen in Figure 11.
The CS4398 does not include phase or amplitude compensation for an external filter. Therefore, the DAC
system phase and amplitude response is dependent on the external analog circuitry.
Figure 11. Recommended Output Filter
4.3
The MUTEC Outputs
The AMUTEC and BMUTEC pins have an auto-polarity detect feature. The MUTEC output pins are high
impedance at the time of reset. The external mute circuitry needs to be self-biased into an active state in
order to be muted during reset. Upon release of reset, the CS4398 detects the status of the MUTEC pins
(high or low) and then selects that state as the polarity to drive when the mutes become active. The external-
bias voltage level that the MUTEC pins see at the time of release of reset must meet the “MUTEC auto de-
tect input high/low voltage” specifications as outlined in the Digital Characteristics in Section 2.
Figure 12 shows a single example of both an active-high and an active-low mute drive circuit. In these de-
signs, the pull-up and pull-down resistors have been specifically chosen to meet the input high/low threshold
when used with the MMUN2111 and MMUN2211 internal bias resistances of 10 k
.
相關PDF資料
PDF描述
AT-S-26-4/4/S-25-R MOD CORD STANDARD 4-4 SILVER 25'
GBM24DCCS-S189 CONN EDGECARD 48POS R/A .156 SLD
AD9744ACP-PCBZ BOARD EVAL FOR AD9744ACP
ORT42G5-EV BOARD EVAL ORT42G5/CABLE/ADAPTER
REF194GS-REEL IC VREF SERIES PREC 4.5V 8-SOIC
相關代理商/技術參數
參數描述
CDB43L21 功能描述:音頻 IC 開發工具 Eval Bd 98dB 96kHz Low-Pwr DAC RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
CDB43L22 功能描述:音頻 IC 開發工具 Eval Bd LP DAC w/ClassD Spkr Driver RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
CDB43L42 功能描述:音頻 IC 開發工具 Eval Bd LP DAC w/Head phn.&Ln Amp RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
CDB43L43 功能描述:音頻 IC 開發工具 Eval Bd LP DAC w/Head phn.&Ln Amp RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
CDB44800 功能描述:音頻 IC 開發工具 Eval Bd 8-Ch 115dB 192kHz PWM RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*