- 您現在的位置：買賣IC網 > PDF目錄366763 > CAT93C4614PI-45TE13 64K 8K x 8 Battery-Voltage CMOS E2PROM PDF資料下載
參數資料
| 型號： | CAT93C4614PI-45TE13 |
| 元件分類： | EEPROM |
| 英文描述： | 64K 8K x 8 Battery-Voltage CMOS E2PROM |
| 中文描述： | 64K的8K的× 8電池電壓的CMOS E2PROM的 |
| 文件頁數： | 9/10頁 |
| 文件大小： | 168K |
| 代理商： | CAT93C4614PI-45TE13 |
9-93
CAT93CXXXX
Stock No. 21084-01 2/98
Advanced Information
Figure 6. EWEN/EWDS Instruction Timing
SK
CS
DI
STANDBY
1
0
0
*
* ENABLE=11
DISABLE=00
entered the self clocking mode. The ready/busy status
of the CAT93CXXXX can be determined by selecting
the device and polling the DO pin. Once cleared, the
contents of all memory bits return to a logical “1” state.
Write All
Upon receiving a WRAL command and data, the CS
(Chip Select) pin must be deselected for a minimum of
t
CSMIN
. The falling edge of CS will start the self clocking
data write to all memory locations in the device. The
clocking of the SK pin is not necessary after the device
has entered the self clocking mode. The ready/busystatus
of the CAT93CXXXXcan be determined by selecting the
device and polling the DO pin. It is not necessary for all
memory locations to be cleared before the WRAL com-
mand is executed.
Erase/Write Enable and Disable
The CAT93CXXXX powers up in the write disable state.
Any writing after power-up or after an EWDS (write
disable) instruction must first be preceded by the EWEN
(write enable) instruction. Once the write instruction is
enabled, it will remain enabled until power to the device
is removed, or the EWDS instruction is sent. The EWDS
instruction can be used to disable all CAT93CXXXX
write and clear instructions, and will prevent any acci-
dental writing or clearing of the device. Data can be read
normally from the device regardless of the write enable/
disable status.
Erase All
Upon receiving an ERAL command, the CS (Chip Se-
lect) pin must be deselected for a minimum of t
CSMIN
.
The falling edge of CS will start the self clocking clear
cycle of all memory locations in the device. The clocking
of the SK pin is not necessary after the device has
Figure 7. ERAL Instruction Timing
SK
CS
DI
DO
STANDBY
tCS
HIGH-Z
HIGH-Z
1
0
1
BUSY
READY
STATUS VERIFY
tSV
tHZ
tEW
0
0
相關PDF資料 |
PDF描述 |
|---|---|
| CAT93C4621PI-45TE13 | 64K 8K x 8 Battery-Voltage CMOS E2PROM |
| CAT93C4622PI-45TE13 | 64K 8K x 8 Battery-Voltage CMOS E2PROM |
| CAT93C5611PI-45TE13 | 64K 8K x 8 Battery-Voltage CMOS E2PROM |
| CAT93C5612PI-45TE13 | 64K 8K x 8 Battery-Voltage CMOS E2PROM |
| CAT93C5613PI-45TE13 | 64K 8K x 8 Battery-Voltage CMOS E2PROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT93C4621 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:Supervisory Circuits with Microwire Serial CMOS E2PROM, Precision Reset Controller and Watchdog Timer |
| CAT93C4621PI-45TE13 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:Supervisory Circuits with Microwire Serial CMOS E2PROM, Precision Reset Controller and Watchdog Timer |
| CAT93C4622 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:Supervisory Circuits with Microwire Serial CMOS E2PROM, Precision Reset Controller and Watchdog Timer |
| CAT93C4622PI-45TE13 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:Supervisory Circuits with Microwire Serial CMOS E2PROM, Precision Reset Controller and Watchdog Timer |
| CAT93C4623 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:Supervisory Circuits with Microwire Serial CMOS E2PROM, Precision Reset Controller and Watchdog Timer |
發布緊急采購，3分鐘左右您將得到回復。