- 您現在的位置：買賣IC網 > PDF目錄366670 > CAT1027ZI-45TE13 Dual Voltage Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM PDF資料下載
參數資料
| 型號： | CAT1027ZI-45TE13 |
| 英文描述： | Dual Voltage Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM |
| 中文描述： | 雙電壓監控電路，帶有I2C串行的2K位CMOS EEPROM的 |
| 文件頁數： | 13/20頁 |
| 文件大小： | 153K |
| 代理商： | CAT1027ZI-45TE13 |
13
CAT1026, CAT1027
Doc No. 3010, Rev. K
Immediate/Current Address Read
The CAT1026 and CAT1027 address counter contains
the address of the last byte accessed, incremented by
one. In other words, if the last READ or WRITE access
was to address N, the READ immediately following
would access data from address N + 1. For N = E = 255,
the counter will wrap around to zero and continue to
clock out valid data. After the CAT1026 and CAT1027
receive a slave address (with the R/
W
bit set t o one), an
acknowledge is issued, and the requested 8-bit byte is
transmitted. The master device does not send an
acknowledge, but will generate a STOP condition.
Selective/Random Read
Selective/Random READ operations allow the Master
device to select at random any memory location for a
READ operation. The Master device first performs a
‘dummy’ write operation by sending the START condition,
slave address and byte addresses of the location it
wishes to read. After the CAT1026 and CAT1027
acknowledge, the Master device sends the START
condition and the slave address again, this time with the
R/
W
bit set to one. The CAT1026 and CAT1027 then
respond with an acknowledge and sends the 8-bit byte
requested. The master device does not send an
acknowledge but will generate a STOP condition.
Sequential Read
The Sequential READ operation can be initiated by
either the Immediate Address READ or Selective READ
operations. After the CAT1026 and CAT1027 send the
inital 8-bit byte requested, the Master responds with an
acknowledge which tells the device it requires more
data. The CAT1026 and CAT1027 will continue to output
an 8-bit byte for each acknowledge, thus sending the
STOP condition.
The data being transmitted from the CAT1026 and
CAT1027 is sent sequentially with the data from address
N followed by data from address N+1. The READ
operation address counter increments all of the CAT1026
and CAT1027 address bits so that the entire memory
array can be read during one operation.
SLAVE
ADDRESS
S
A
C
K
N
O
A
C
K
S
T
O
P
P
BUS ACTIVITY:
MASTER
SDA LINE
S
T
A
R
T
BYTE
ADDRESS (n)
S
A
C
K
DATA n
SLAVE
ADDRESS
A
C
K
S
T
A
R
T
BUS ACTIVITY:
MASTER
SDA LINE
DATA n+x
DATA n
A
C
K
A
C
K
DATA n+1
A
C
K
S
T
O
P
N
O
A
C
K
DATA n+2
A
C
K
P
SLAVE
ADDRESS
Figure 12. Selective Read Timing
Figure 13. Sequential Read Timing
相關PDF資料 |
PDF描述 |
|---|---|
| CAT1026PE-45TE13 | Dual Voltage Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM |
| CAT1026PI-42TE13 | Dual Voltage Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM |
| CAT1026PI-45TE13 | Dual Voltage Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM |
| CAT1026RD4E-30TE13 | Dual Voltage Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM |
| CAT1026RD4E-42TE13 | Dual Voltage Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT102EUK-TE7 | 功能描述:基準電壓& 基準電流 600mV w/Open Colectr RoHS:否 制造商:STMicroelectronics 產品:Voltage References 拓?fù)浣Y(jié)構:Shunt References 參考類型:Programmable 輸出電壓:1.24 V to 18 V 初始準確度:0.25 % 平均溫度系數（典型值）:100 PPM / C 串聯 VREF - 輸入電壓（最大值）: 串聯 VREF - 輸入電壓（最小值）: 分流電流（最大值）:60 mA 最大工作溫度:+ 125 C 封裝 / 箱體:SOT-23-3L 封裝:Reel |
| CAT102TBI-GTE7 | 功能描述:直流/直流開關轉換器 600mV Adj RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| CAT102TDI-GT3 | 功能描述:直流/直流開關轉換器 Prec,Adj Shunt Reg 600mV RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| CAT10-300J4 | 功能描述:電阻器網絡與陣列 30ohm 5% Concave 4resistors RoHS:否 制造商:Vishay/Thin Film 產品類型:Networks 電路類型:Divider 電阻器數量: 電阻數值:10 kOhms 容差:0.1 % 溫度系數: 管腳數量:3 工作溫度范圍:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引線間隔: 端接類型:SMD/SMT 封裝:Reel |
| CAT10-300J4LF | 功能描述:電阻器網絡與陣列 30ohm 5% Concave 4resistors RoHS:否 制造商:Vishay/Thin Film 產品類型:Networks 電路類型:Divider 電阻器數量: 電阻數值:10 kOhms 容差:0.1 % 溫度系數: 管腳數量:3 工作溫度范圍:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引線間隔: 端接類型:SMD/SMT 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。