- 您現在的位置：買賣IC網 > PDF目錄1907 > C88F83B0AU-TC-H (ON Semiconductor)MCU 16BIT 256K LCD 120-TQFP PDF資料下載
參數資料
| 型號： | C88F83B0AU-TC-H |
| 廠商： | ON Semiconductor |
| 文件頁數： | 21/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | MCU 16BIT 256K LCD 120-TQFP |
| 標準包裝： | 90 |
| 核心處理器： | Xstormy16 |
| 芯體尺寸： | 16-位 |
| 速度： | 4.2MHz |
| 連通性： | SIO，UART/USART |
| 外圍設備： | LCD，WDT |
| 輸入/輸出數： | 20 |
| 程序存儲器容量： | 128KB（128K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 4K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.3 V ~ 5.5 V |
| 數據轉換器： | A/D 4x12b |
| 振蕩器型： | 內部 |
| 工作溫度： | -20°C ~ 75°C |
| 封裝/外殼： | 120-TQFP |
| 包裝： | 托盤 |
LC88F83B0A
No.A1228-5/25
Standby Function
HALT mode: Halts instruction execution while allowing the peripheral circuits to continue operation.
1) Oscillation is not halted automatically.
2) Released by a system reset or occurrence of an interrupt.
HOLD mode: Suspends instruction execution and the operation of the peripheral circuits.
1) OSC1, internal RC and X’tal oscillators automatically stop operation.
2) There are the following methods of resetting the HOLD.
(1) Setting the reset pin to the low level
(2) Having an interrupt source established in the SIO0
(3) Having an interrupt source established in the UART2
(4) Having an interrupt source established in the P00 to P05
(5) Having an interrupt source established in the SEG71 to SEG64
X’tal HOLD mode: Suspends instruction execution and the operation of the peripheral circuits except using OSC0.
1) The OSC1 and internal RC oscillators automatically stop operation.
2) The state of OSC0 oscillation established when the X'tal HOLD mode is entered is retained.
3) There are the following methods of resetting the X'tal HOLD mode.
(1) Setting the reset pin to the low level
(2) Having an interrupt source established in the base timer circuit
(3) Having an interrupt source established in the timers 0, 1, 3, 4, 5
(4) Having an interrupt source established in the SIO0
(5) Having an interrupt source established in the UART2
(6) Having an interrupt source established in the P00 to P05
(7) Having an interrupt source established in the SEG71 to SEG64
On-chip debugger
Supports software debugging with the IC mounted on the target board.
Supports tracing, realtime monitoring, and breakpoint setting.
Single-wire communication
Package Form
TQFP120(14×14): Lead-free type
Development Tools
On-chip debugger
: EOCUIF1 + LC88F83B0A
Programming boards :
Package Dimensions
unit : mm (typ)
3257A
SANYO : TQFP120(14X14)
0.125
120
0.15
0.4
(1.2)
1
14.0
16.0
14.
0
16.
0
1.
2MAX
0.
1
(1.0)
0.
5
相關PDF資料 |
PDF描述 |
|---|---|
| CAT5112VI-10-T3 | IC POT DIGITL 10K 32TAP 8SOIC |
| CAT5113ZI01 | IC POT DPP NV 100TAP U/D 8MSOP |
| CAT5115ZI-50-G | IC POT DIG 50K 32TAP 8MSOP |
| CAT5116LI-G | IC POT DIG LOG 32K 100TAP 8DIP |
| CAT5119SDI-50-T3 | IC DPP MINIPOT 32TAP U/D SC70-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| C88F85D0AU-TC-H | 功能描述:16位微控制器 - MCU LCD DIVIDER CIRCUIT RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| C89-0030 | 制造商:N/A 功能描述: |
| C89003Y-100-ND | 功能描述:18/3 ULTRA FLEX SJEOOW 100' YEL RoHS:是 類別:線纜，導線 >> 多芯導線 系列:Ultra Flex® 標準包裝:1 系列:* |
| C89003Y-10-ND | 功能描述:18/3 ULTRA FLEX SJEOOW 10' YEL RoHS:是 類別:線纜，導線 >> 多芯導線 系列:Ultra Flex® 標準包裝:1 系列:* |
| C89003Y-25-ND | 功能描述:18/3 ULTRA FLEX SJEOOW 25' YEL RoHS:是 類別:線纜，導線 >> 多芯導線 系列:Ultra Flex® 標準包裝:1 系列:* |
發布緊急采購，3分鐘左右您將得到回復。