參數資料
型號: C8051F931-GM
廠商: Silicon Laboratories Inc
文件頁數: 300/330頁
文件大?。?/td> 0K
描述: IC 8051 MCU 64K FLASH 24-QFN
產品培訓模塊: C8051F9xx Lower Power MCUs
Serial Communication Overview
視頻文件: Designing for Low Power Operation
特色產品: C8051F91x/0x MCU Series Development Kit
標準包裝: 91
系列: C8051F9xx
核心處理器: 8051
芯體尺寸: 8-位
速度: 25MHz
連通性: SMBus(2 線/I²C),SPI,UART/USART
外圍設備: 欠壓檢測/復位,POR,PWM,溫度傳感器,WDT
輸入/輸出數: 16
程序存儲器容量: 64KB(64K x 8)
程序存儲器類型: 閃存
RAM 容量: 4.25K x 8
電壓 - 電源 (Vcc/Vdd): 0.9 V ~ 3.6 V
數據轉換器: A/D 15x10b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 24-WFQFN 裸露焊盤
包裝: 托盤
產品目錄頁面: 625 (CN2011-ZH PDF)
配用: 336-1479-ND - PLATFORM PROG TOOLSTCK F921,F931
336-1476-ND - DAUGHTER CARD CAP TOUCH SENSE
336-1475-ND - KIT STARTER CAP TOUCH SENSE
336-1474-ND - DAUGHTER CARD TOOLSTCK C8051F931
336-1473-ND - KIT DEV C8051F920,F921,F930,F931
其它名稱: 336-1468
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁第255頁第256頁第257頁第258頁第259頁第260頁第261頁第262頁第263頁第264頁第265頁第266頁第267頁第268頁第269頁第270頁第271頁第272頁第273頁第274頁第275頁第276頁第277頁第278頁第279頁第280頁第281頁第282頁第283頁第284頁第285頁第286頁第287頁第288頁第289頁第290頁第291頁第292頁第293頁第294頁第295頁第296頁第297頁第298頁第299頁當前第300頁第301頁第302頁第303頁第304頁第305頁第306頁第307頁第308頁第309頁第310頁第311頁第312頁第313頁第314頁第315頁第316頁第317頁第318頁第319頁第320頁第321頁第322頁第323頁第324頁第325頁第326頁第327頁第328頁第329頁第330頁
Rev. 1.4
71
C8051F93x-C8051F92x
5.2.3. Burst Mode
Burst Mode is a power saving feature that allows ADC0 to remain in a low power state between conver-
sions. When Burst Mode is enabled, ADC0 wakes from a low power state, accumulates 1, 4, 8, 16, 32, or
64 using an internal burst mode clock (approximately 25 MHz), then re-enters a low power state. Since the
burst mode clock is independent of the system clock, ADC0 can perform multiple conversions then enter a
low power state within a single system clock cycle, even if the system clock is slow (e.g., 32.768 kHz), or
suspended.
Burst Mode is enabled by setting BURSTEN to logic 1. When in burst mode, AD0EN controls the ADC0
idle power state (i.e. the state ADC0 enters when not tracking or performing conversions). If AD0EN is set
to logic 0, ADC0 is powered down after each burst. If AD0EN is set to logic 1, ADC0 remains enabled after
each burst. On each convert start signal, ADC0 is awakened from its Idle Power State. If ADC0 is powered
down, it will automatically power up and wait the programmable Power-Up Time controlled by the
AD0PWR bits. Otherwise, ADC0 will start tracking and converting immediately. Figure 5.3 shows an exam-
ple of Burst Mode Operation with a slow system clock and a repeat count of 4.
When burst mode is enabled, a single convert start will initiate a number of conversions equal to the repeat
count. When burst mode is disabled, a convert start is required to initiate each conversion. In both modes,
the ADC0 End of Conversion Interrupt Flag (AD0INT) will be set after “repeat count” conversions have
been accumulated. Similarly, the Window Comparator will not compare the result to the greater-than and
less-than registers until “repeat count” conversions have been accumulated.
In Burst Mode, tracking is determined by the settings in AD0PWR and AD0TK. The default settings for
these registers will work in most applications without modification; however, settling time requirements may
need adjustment in some applications. Refer to “5.2.4. Settling Time Requirements” on page 73 for more
details.
Notes:
Setting AD0TM to 1 will insert an additional 3 SAR clocks of tracking before each conversion, regardless of the
settings of AD0PWR and AD0TK.
When using Burst Mode, care must be taken to issue a convert start signal no faster than once every four
SYSCLK
periods. This includes external convert start signals.
A rising edge of external start-of-conversion (CNVSTR) will cause only one ADC conversion in Burst
Mode, regardless of the value of the Repeat Count field. The end-of-conversion interrupt will occur
after the number of conversions specified in Repeat Count have completed. In other words, if Repeat
Count is set to 4, four pulses on CNVSTR will cause an ADC end-of-conversion interrupt. Refer to the
for an example.
To start multiple conversions in Burst Mode with one external start-of-conversion signal, the external
interrupts (/INT0 or /INT1) or Port Match can be used to trigger an ISR that writes to AD0BUSY. Exter-
nal interrupts are configurable to be active low or active high, edge or level sensitive, but is only avail-
able on a limited number of pins. Port Match is only level sensitive, but is available on more port pins
than the external interrupts. Refer to Section “12.6. External Interrupts INT0 and INT1” on
for details on external interrupts and Section “21.4. Port Match” on page 227 for details on
Port Match.
相關PDF資料
PDF描述
P87LPC762FD,512 IC 80C51 MCU 2K OTP 20-SOIC
MC68HC908JK3CP IC MCU 8MHZ 4K FLASH 20-DIP
MC68HC908JK3CDW IC MCU 8MHZ 4K FLASH 20-SOIC
MC68HC908JK1CP IC MCU 8MHZ 1.5K FLASH 20-DIP
MC68HC908JK1CDW IC MCU 8MHZ 1.5K FLASH 20-SOIC
相關代理商/技術參數
參數描述
C8051F931-GMR 功能描述:8位微控制器 -MCU 64KB 10ADC MCU LEAD FREE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F93X 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single/Dual Battery, 0.9–3.6 V, 64/32 kB, smaRTClock, 10-Bit ADC MCU
C8051F960-A-DK 功能描述:開發板和工具包 - 8051 C8051F96X Development Kit RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓:
C8051F960-A-GM 功能描述:8位微控制器 -MCU 128KB, DC-DC, LCD AES, DQFN76 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F960-A-GMR 制造商:Silicon Laboratories Inc 功能描述:128KB, DC-DC, LCD, AES, DQFN76 - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:IC MCU 128KB DC-DC LCDAES 76DQFN