- 您現在的位置：買賣IC網 > PDF目錄385199 > BU9877FV (Rohm CO.,LTD.) Serial interface IC for DIMMs supporting plug & play PDF資料下載
參數資料
| 型號： | BU9877FV |
| 廠商： | Rohm CO.,LTD. |
| 英文描述： | Serial interface IC for DIMMs supporting plug & play |
| 中文描述： | 對DIMM的串行接口芯片，支持即插即用 |
| 文件頁數： | 6/9頁 |
| 文件大?。?/td> | 95K |
| 代理商： | BU9877FV |
SCL
(from master)
SDA
(master output data)
SDA
(data output from the BU9877FV)
Acknowledge signal (ACK signal)
Start condition
t PD
Fig. 6 Acknowledge signal (ACK signal) response
(when slave address is input for writing or reading)
1
8
9
6
Memory ICs
BU9877FV
(7) Write protect command
The write protect command is used to prohibit writing of
data to addresses 00 to 7Fh, among the 256 word
address data. Be aware that once a write protect regis-
ter has been specified, it cannot be canceled (one-time
memory). The write protect command can function
regardless of the state of the WP pin.
(8) WP (write protect pin)
Setting the WP pin to Vcc (HIGH level) has the same
effect as using the write protect command, and inhibits
writing of data to addresses 80 to FFh, among the 256
word address data. Normal writing is enabled by set-
ting this pin to GND (LOW level). (If the write protect
command is used to inhibit writing, data cannot be writ-
ten regardless of the status of the WP pin.) The WP pin
is equipped with an internal pull-down resistor, so if the
protect function is not being used, this should be left
open or set to GND.
(9) ACK signal
The acknowledge signal (ACK signal) is determined by
the software, and indicates whether or not the data has
been correctly transmitted. Regardless of whether the
address is a master or slave address, the device on the
transmitter (sending signal) side (the master when a
slave address is input for a write command or a read
command, and the EEPROM when read command
data is output) opens the bus after this 8-bit data is out-
put. With a device on the receiving (reception) side (the
EEPROM when a slave address is input for a read
command or write command, and the master when
data is output for a read command), SDA is set to LOW
during the nine-clock cycle, and the acknowledge sig-
nal (ACK signal) is output when 8-bit data is received.
For writing operations, the acknowledge signal (ACK
signal) is output in the LOW state each time that 8-bit
data (word address or write data) is received.
In reading operations, 8-bit data (read data) is output,
and then the acknowledge signal (ACK signal) in the
LOW state is detected. If the acknowledge signal (ACK
signal) is detected and no stop condition is sent from
the master (microcomputer) side, this IC continues to
output data. If the acknowledge signal (ACK signal) is
not detected, this IC interrupts the transmission of data,
recognizes a stop condition (stop bit), and terminates
the reading operation. The IC then enters the standby
mode.
相關PDF資料 |
PDF描述 |
|---|---|
| BUF725D | SILICON NPN HIGH VOLTAGE SWITCHING TRANSISTOR |
| BUJ100LR | NPN power transistor |
| BUJ100 | NPN power transistor |
| BUJ103AD | NPN power transistor |
| BUJ103AX | NPN power transistor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BU9880GUL-W | 制造商:ROHM 制造商全稱:Rohm 功能描述:WL-CSP EEPROM family I2C BUS |
| BU9880GUL-W_10 | 制造商:ROHM 制造商全稱:Rohm 功能描述:WL-CSP EEPROM family I2C BUS |
| BU9880GUL-WE2 | 功能描述:電可擦除可編程只讀存儲器 電可擦除可編程只讀存儲器 Serial-2Wire 64Kb RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| BU9881 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| BU9881F | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
發布緊急采購，3分鐘左右您將得到回復。