- 您現在的位置：買賣IC網 > PDF目錄385186 > bq2050 (Benchmark Technology Group) Lithium Ion Power Gauge IC(鋰離子電源Gause 芯片) PDF資料下載
參數資料
| 型號： | bq2050 |
| 廠商： | Benchmark Technology Group |
| 英文描述： | Lithium Ion Power Gauge IC(鋰離子電源Gause 芯片) |
| 中文描述： | 鋰離子動力計IC（鋰離子電源高斯芯片） |
| 文件頁數： | 13/21頁 |
| 文件大?。?/td> | 235K |
| 代理商： | BQ2050 |
Nominal Available Charge Registers
(NACH/NACL)
The read/write NACH high-byte register (address=03h) and
the read-only NACL low-byte register (address=17h) are
the main gas gauging register for the bq2050. The NAC
registers are incremented during charge actions and decre-
mented during discharge and self-discharge actions. The
correction factors for charge/discharge efficiency are applied
automatically to NAC. NACH and NACL are set to 0 dur-
ingabq2050reset.
Writ
ing to the NAC registers affects the available charge
counts and, therefore, affects the bq2050 gas gauge opera-
tion. Do not write the NAC registers to a value greater than
LMD.
Battery Identification Register (BATID)
The read/write BATID register (address=04h) is avail-
able for use by the system to determine the type of bat-
tery pack. The BATID contents are retained as long as
V
CC
is greater than 2V. The contents of BATID have no
effect on the operation of the bq2050. There is no de-
fault setting for this register.
Last Measured Discharge Register (LMD)
LMD is a read/write register (address=05h) that the
bq2050 uses as a measured full reference. The bq2050
adjusts LMD based on the measured discharge capacity
of the battery from full to empty. In this way the bq2050
updates the capacity of the battery. LMD is set to PFC
during a bq2050 reset.
Secondary Status Flags Register (FLGS2)
The read-only FLGS2 register (address=06h) contains
the secondary bq2050 flags.
The
discharge rate
flags,DR2–0,are bits 6–4.
They are used to determine the current discharge re-
gime as follows:
The
overload
flag (OVLD) is asserted when a discharge
rate in excess of 2C is detected. OVLD remains asserted
as long as the condition persists and is cleared 0.5 sec-
onds after the rate drops below 2C. The overload condi-
tion is used to stop sampling of the battery terminal char-
acteristics for end-of-discharge determination.
ProgramPinPull-DownRegister(PPD)
The read-only PPD register (address=07h) contains some
of the programming pin information for the bq2050. The
segment drivers, SEG
1–6
, have a corresponding PPD regis-
ter location, PPD
1–6
. A given location is set if a pull-down
resistor has been detected on its corresponding segment
driver. For example, if SEG
1
and SEG
4
have pull-down
resistors,the contents of PPD are xx001001.
Program Pin Pull-Up Register (PPU)
The read-only PPU register (address=08h) contains the rest
of the programming pin information for the bq2050. The
segment drivers, SEG
1–6
, have a corresponding PPU regis-
ter location, PPU
1–6
. A given location is set if a pull-up re-
sistor has been detected on its corresponding segment
13
bq2050
TMP3
0
0
0
0
0
0
0
0
1
1
1
1
1
TMP2
0
0
0
0
1
1
1
1
0
0
0
0
1
TMP1
0
0
1
1
0
0
1
1
0
0
1
1
0
TMP0
0
1
0
1
0
1
0
1
0
1
0
1
0
Temperature
T < -30°C
-30°C < T < -20°C
-20°C < T < -10°C
-10°C < T < 0°C
0°C < T < 10°C
10°C < T < 20°C
20°C < T < 30°C
30°C < T < 40°C
40°C < T < 50°C
50°C < T < 60°C
60°C < T < 70°C
70°C < T < 80°C
T > 80°C
Table 7. Temperature Register
FLGS2 Bits
4
DR1
7
-
6
5
3
-
2
-
1
-
0
DR2
DR0
DR2
0
0
0
DR1
0
0
1
DR0
0
1
0
Discharge Rate
DRATE
<
0.5C
0.5C
≤
DRATE
<
2C
DRATE
≥
2C (OVLD = 1)
FLGS2 Bits
4
-
7
-
6
-
5
-
3
-
2
-
1
-
0
OVLD
TMPGG Gas Gauge Bits
7
6
5
4
3
2
1
0
-
-
-
-
GG3
GG2
GG1
GG0
相關PDF資料 |
PDF描述 |
|---|---|
| bq2052 | Gas Gauge IC for Lithium Primary Cells(Gas Gauge 芯片（用于鋰電池）) |
| bq2060 | SBS v1.1-Compliant Gas Gauge IC(Gas Gauge芯片) |
| bq2092 | Gas Gauge IC with SMBus-Like Interface(Gas Gauge芯片（帶SMBus 接口）) |
| bq2201 | SRAM Nonvolatile Controller Unit(靜態RAM非易失性控制器單元) |
| bq2202 | SRAM Nonvolatile Controller With Reset(靜態RAM非易失性控制器單元(帶復位）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ2050H | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low-Cost Lithium Ion Power Gauge IC |
| bq2050hevm | 制造商:Texas Instruments 功能描述: |
| BQ2050HEVM-002 | 功能描述:電源管理IC開發工具 BQ2050H Eval Kit for Li-Ion 10.8V RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| BQ2050HSN | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low-Cost Lithium Ion Power Gauge IC |
| BQ2050HSN-A308 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low-Cost Lithium Ion Power Gauge IC |
發布緊急采購，3分鐘左右您將得到回復。