- 您現在的位置：買賣IC網 > PDF目錄385186 > bq2040 (Benchmark Technology Group) Gas Gauge IC With SMBus Interface(氣體Gauge芯片（帶SMBus 接口）) PDF資料下載
參數資料
| 型號： | bq2040 |
| 廠商： | Benchmark Technology Group |
| 英文描述： | Gas Gauge IC With SMBus Interface(氣體Gauge芯片（帶SMBus 接口）) |
| 中文描述： | 氣體計IC，帶有SMBus接口（氣體計芯片（帶的SMBus接口）） |
| 文件頁數： | 7/32頁 |
| 文件大?。?/td> | 189K |
| 代理商： | BQ2040 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
ing subsequent discharges, FCC is updated with the
latest measured capacity in the Discharge Count Reg-
ister plus the battery low amount, representing a dis-
charge from full to below EDV1.
charge is necessary for a capacity transfer from the
DCR to the FCC register. Once updated, the bq2040
writes the new FCC to the EEPROM. The FCC also
serves as the 100% reference threshold used by the
relative state-of-charge calculation and display.
A qualified dis-
2.
DesignCapacity (DC):
The DC is the user-specified battery capacity and is
programmed from external EEPROM. The DC also
provides the 100% reference for the absolute dis-
play mode.
3.
RemainingCapacity (RM):
RM counts up during charge to a maximum value of
FCC and down during discharge and self-discharge to
0.
RM is set to the battery low amount after the
EDV1 threshold has been reached. If RM is already
equal to or less than the battery low amount, RM is
not modified. If RM reaches the battery low amount
before the battery voltage falls below EDV1 on dis-
charge, RM stops counting down until the EDV1
threshold is reached. RM is set to 0 when the battery
voltage reaches EDVF. To prevent overstatement of
charge during periods of overcharge, RM stops in-
crementing when RM = FCC. RM may optionally
be written to a user-defined value when fully
charged if the battery pack is under bq2040 charge
control. On initialization,RM is set to 0.
4.
Discharge Count Register (DCR):
The DCR counts up during discharge independent
of RM and can continue increasing after RM has
decremented to 0. Prior to RM = 0, both discharge
and self-discharge increment the DCR. After RM
= 0, only discharge increments the DCR. The DCR
resets to 0 when RM = FCC and stops counting at
EDV1 on discharge. The DCR does not roll over but
stops counting when it reaches FFFFh.
FCC is updated on the first charge after a qualified
discharge to EDV1. The updated FCC equals the
battery low percentage times the current FCC plus
the DCR value. A qualified discharge to EDV1 oc-
curs if all of the following conditions exist:
No valid charge initiations (charges greater than
10mAh, where V
SRO
> +V
SRD
occurred during
the period between RM = FCC and EDV1 de-
tected.
The self-discharge count is not more than
256mAh.
The low temperature fault bit in FLAGS2 is not
set when the EDV1 level is reached during dis-
charge.
Battery voltage is not more than 256mV below
the EDV1 threshold when EDV1 is set.
The valid discharge flag (VDQ) in FLAGS1 indi-
cates whether the present discharge is valid for an
FCC update. FCC cannot be reduced by more than
256mAh during any single cycle.
7
bq2040
FG294501.eps
Temperature
Compensation
Charge
Current
Discharge
Current
Self-Discharge
Timer
Remaining
Capacity
(RM)
Full
Charge
Capacity
(FCC)
Discharge
Count
Register
(DCR)
<
Qualified
Transfer
+
Temperature, Other Data
+
-
-
+
Inputs
Main Counters
and Capacity
Reference (FCC)
Outputs
Two-Wire
Serial Interface
Chip-Controlled
Available Charge
LED Display
State-of-charge
Te and
Figure 2. Operational Overview
相關PDF資料 |
PDF描述 |
|---|---|
| bq2050H | Low-Cost Lithium Ion Power Gauge IC(低價格鋰離子電源氣體Gauge芯片) |
| bq2050 | Lithium Ion Power Gauge IC(鋰離子電源Gause 芯片) |
| bq2052 | Gas Gauge IC for Lithium Primary Cells(Gas Gauge 芯片（用于鋰電池）) |
| bq2060 | SBS v1.1-Compliant Gas Gauge IC(Gas Gauge芯片) |
| bq2092 | Gas Gauge IC with SMBus-Like Interface(Gas Gauge芯片（帶SMBus 接口）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ2040EVM-001 | 功能描述:電源管理IC開發工具 Eval Kit for NiMH 10.8V RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| BQ2040SN | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Gas Gauge IC With SMBus Interface |
| BQ2040SN | 制造商:Texas Instruments 功能描述:BATTERY CHARGE MONITOR SMD 2040 |
| BQ2040SN-C408 | 功能描述:電池管理 Multi-Chemistry SBS RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ2040SN-C408 | 制造商:Texas Instruments 功能描述:Battery Management IC |
發布緊急采購，3分鐘左右您將得到回復。