參數資料
型號: bq2040
廠商: Benchmark Technology Group
英文描述: Gas Gauge IC With SMBus Interface(氣體Gauge芯片(帶SMBus 接口))
中文描述: 氣體計IC,帶有SMBus接口(氣體計芯片(帶的SMBus接口))
文件頁數: 16/32頁
文件大小: 189K
代理商: BQ2040
Output: unsigned integer. Returns the minutes of
operation left.
Units: minutes
Range: 0 to 65,534min
Granularity: 2min or better
Invalid data indication: 65,535 indicates battery
is not being discharged.
AverageTimeToFull() (0x13)
This read-only word returns the predicted time until the
Smart Battery reaches full charge at the present aver-
age charge rate (minutes).
Output:
time in minutes to full.
unsigned integer. Returns the remaining
Units: minutes
Range: 0 to 65,534min
Granularity: 2min or better
Invalid data indication: 65,535 indicates battery
is not being charged.
ChargingCurrent() (0x14)
If enabled, the bq2040 sends the desired charging rate in
mA to the Smart Battery Charger.
Output:
maximumchargeroutputcurrentinmA.
unsigned integer.
Transmits/returns the
Units: mA
Range: 0 to 65,534mA
Granularity: 0.2% of the design capacity or better
Invalid data indication:
Smart Charger should operate as a voltage source
outside its maximum regulated current range.
65,535 indicates that the
ChargingVoltage() (0x15)
If enabled, the bq2040 sends the desired voltage in mV
to the Smart Battery Charger.
Output: unsigned integer. Transmits/returns the
charger voltage output in mV.
Units: mV
Range: 0 to 65,534mV
Granularity: 0.2% of the DesignVoltage or better
Invalid data indication: 65,535 indicates that the
Smart Battery Charger should operate as a cur-
rent source outside its maximum regulated voltage
range.
BatteryStatus() (0x16)
This read-only word returns the battery status word.
Output: unsigned integer. Returns the status reg-
ister with alarm conditions bitmapped as shown in
Table 5.
Some of the BatteryStatus flags (Remaining_Capac-
ity_Alarm and Remaining_Time_Alarm) are calculated
based on current. See Table 8 and 9 for definitions.
CycleCount() (0x17)
This read-only word returns the number of charge/dis-
charge cycles the battery has experienced. A charge/dis-
charge cycle starts from a base value equivalent to the
battery's state-of-charge on completion of a charge cycle.
The bq2040 increments the cycle counter during the cur-
rent charge cycle if the battery has been discharged 15%
below the state-of-charge at the end of the last charge cy-
cle. This prevents false reporting of small charge/discharge
cycles.
The cycle count is stored in EEPROM within
400ms of an update.
Output: unsigned integer. Returns the count of
charge/discharge cycles the battery has
experienced.
Units:cycles
16
bq2040
Alarm Bits
Over_Charged_Alarm
Terminate_Charge_Alarm
Reserved
Over_Temp_Alarm
Terminate_Discharge_Alarm
Reserved
Remaining_Capacity_Alarm
Remaining_Time_Alarm
Status Bits
Initialized
Discharging
Fully_Charged
Fully_Discharged
Error Code
0x8000
0x4000
0x2000
0x1000
0x0800
0x0400
0x0200
0x0100
0x0080
0x0040
0x0020
0x0010
0x0000-
0x000f
Reserved for error codes
Table 5. Status Register
相關PDF資料
PDF描述
bq2050H Low-Cost Lithium Ion Power Gauge IC(低價格鋰離子電源氣體Gauge芯片)
bq2050 Lithium Ion Power Gauge IC(鋰離子電源Gause 芯片)
bq2052 Gas Gauge IC for Lithium Primary Cells(Gas Gauge 芯片(用于鋰電池))
bq2060 SBS v1.1-Compliant Gas Gauge IC(Gas Gauge芯片)
bq2092 Gas Gauge IC with SMBus-Like Interface(Gas Gauge芯片(帶SMBus 接口))
相關代理商/技術參數
參數描述
BQ2040EVM-001 功能描述:電源管理IC開發工具 Eval Kit for NiMH 10.8V RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
BQ2040SN 制造商:TI 制造商全稱:Texas Instruments 功能描述:Gas Gauge IC With SMBus Interface
BQ2040SN 制造商:Texas Instruments 功能描述:BATTERY CHARGE MONITOR SMD 2040
BQ2040SN-C408 功能描述:電池管理 Multi-Chemistry SBS RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
BQ2040SN-C408 制造商:Texas Instruments 功能描述:Battery Management IC