- 您現在的位置：買賣IC網 > PDF目錄385186 > bq2014H (Benchmark Technology Group) Low-Cost NiCd/NiMH Gas Gauge IC(低價格NiCd/NiMHGas Gauge芯片) PDF資料下載
參數資料
| 型號： | bq2014H |
| 廠商： | Benchmark Technology Group |
| 英文描述： | Low-Cost NiCd/NiMH Gas Gauge IC(低價格NiCd/NiMHGas Gauge芯片) |
| 中文描述： | 低成本鎳鎘/鎳氫電池電量監測計芯片（低價格鎳鎘/ NiMHGas計芯片） |
| 文件頁數： | 7/22頁 |
| 文件大?。?/td> | 185K |
| 代理商： | BQ2014H |
Select:
PFC = 27648 counts or 173mVh
PROG
1
= low
PROG
2
= high
PROG
3
= float
PROG
4
= low
PROG
5
= low
The initial full battery capacity is 173mVh
(3460mAh) until the bq2014H “l(fā)earns” a new capac-
ity with a qualified discharge from full to EDV1.
3.
Nominal Available Capacity (NAC):
NAC counts up during charge to a maximum value
of LMD and down during discharge and self-dis-
charge to 0. NAC is reset to 0 on initialization and
on the first valid charge following discharge to
EDV1. To prevent overstatement of charge during
periods of overcharge, NAC stops incrementing
when NAC = LMD or 0.94
LMD if T < 0
°
C.
4.
Discharge Count Register (DCR):
The DCR counts up during discharge independent
of NAC and could continue increasing after NAC
has decremented to 0.
Prior to NAC = 0 (empty
battery), both discharge and self-discharge in-
crement the DCR. After NAC = 0, only discharge
increments the DCR. The DCR resets to 0 when
NAC
≥
0.94
LMD and a discharge is detected. The
DCR does not roll over but stops counting when it
reaches FFh.
The DCR value becomes the new LMD value on the
first charge after a valid discharge to V
EDV1
if all
the following conditions are met:
I
No valid charge initiations (charges greater than
2 NAC updates where V
SRO
> V
SRQ
) occurred
during the period between NAC
≥
0.94
LMD and
EDV1.
I
The self-discharge is less than 6.25% of NAC.
I
The temperature is
≥
0°C when the EDV1 level
is reached during discharge.
I
The discharge begins when NAC
≥
0.94
LMD.
I
VDQ is set.
The valid discharge flag (VDQ) indicates whether
the present discharge is valid for LMD update. If
the DCR update value is less than 0.94
LMD,
LMD will only be modified by 0.94
LMD. This pre-
ventsinvalidDCRvaluesfromcorruptingLMD.
5.
Scaled Available Energy (SAE):
SAE is useful in determining the available energy
within the battery, and may provide a more useful
capacity reference in battery chemistries with
sloped voltage profiles during discharge. SAE may
be converted to an mWh value using the following
formula:
E(mWh) = (SAEH
1 2
SAEL)
+ R
B2
+
256
(R
R
B2
SCALE
)
R
B1
S
where R
B1
, R
B2
, and R
S
are resistor values in
ohms, as shown in Figure 1. SCALE is the selected
scale from Table 2.
6. Compensated Available Capacity (CACT)
CACT counts similarly to NAC, but contains the
available capacity compensated for discharge rate
and temperature.
Charge Counting
Charge activity is detected based on a positive voltage
on the SR input.
If charge activity is detected, the
bq2014H increments NAC at a rate proportional to V
SR
and,if enabled,activates the LED display.
The bq2014H counts charge activity when the voltage at
the SR input (V
SRO
) exceeds the minimum charge
threshold (V
SRQ
). A valid charge is detected when NAC
has been updated twice without discharging or reaching
the digital magnitude filter time-out.
charge is detected, charge counting continues until V
SR
,
including offset,falls below V
SRQ
.
Once a valid
Discharge Counting
Discharge activity is indicated by a negative voltage on
the SR input. All discharge counts where V
SRO
is less
than the minimum discharge threshold (V
SRD
) cause
the NAC register to decrement and the DCR to
increment.
Self-Discharge Counting
The bq2014H continuously decrements NAC and incre-
ments DCR for self-discharge on the basis of time and tem-
perature.
Charge/Discharge Current
The bq2014H current-scale registers, VSRH and VSRL,
can be used to determine the battery charge or dis-
charge current. See the Current Scale Register descrip-
tion for details.
7
Preliminary
bq2014H
相關PDF資料 |
PDF描述 |
|---|---|
| bq2014 | Gas Gauge IC with External Charge Control(氣體Gauge（帶外部電荷控制）) |
| bq2040 | Gas Gauge IC With SMBus Interface(氣體Gauge芯片（帶SMBus 接口）) |
| bq2050H | Low-Cost Lithium Ion Power Gauge IC(低價格鋰離子電源氣體Gauge芯片) |
| bq2050 | Lithium Ion Power Gauge IC(鋰離子電源Gause 芯片) |
| bq2052 | Gas Gauge IC for Lithium Primary Cells(Gas Gauge 芯片（用于鋰電池）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ2014HEVM-001 | 功能描述:電源管理IC開發工具 BQ2014H Eval Kit for NiMH 10.8V RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| BQ2014HSN | 功能描述:電池管理 NiCd/NiMH Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ2014HSN-A309 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low-Cost NiCd/NiMH Gas Gauge IC |
| BQ2014HSNG4 | 功能描述:電池管理 NiCd/NiMH Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ2014HSNTR | 功能描述:電池管理 NiCd/NiMH Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。