- 您現在的位置：買賣IC網 > PDF目錄385186 > bq2014H (Benchmark Technology Group) Low-Cost NiCd/NiMH Gas Gauge IC(低價格NiCd/NiMHGas Gauge芯片) PDF資料下載
參數資料
| 型號： | bq2014H |
| 廠商： | Benchmark Technology Group |
| 英文描述： | Low-Cost NiCd/NiMH Gas Gauge IC(低價格NiCd/NiMHGas Gauge芯片) |
| 中文描述： | 低成本鎳鎘/鎳氫電池電量監測計芯片（低價格鎳鎘/ NiMHGas計芯片） |
| 文件頁數： | 16/22頁 |
| 文件大小： | 185K |
| 代理商： | BQ2014H |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁
RCAC varies from 0 to 64h representing relative state-
of-charge from 0 to 100%.
Current Scale Register (VSRH/VSRL)
The VSRH register (address = 12h) and the VSRL regis-
ter (address = 13h) report the average signal across the
SR and V
SS
pins. The bq2050H updates this register
pair every 22.5s. V
SRH
(high-byte) and V
SRL
(low-byte)
form a 16-bit signed integer value representing the aver-
age current during this time. The battery pack current
can be calculated from:
|I(mA)| = (V
SRH
256 + V
SRL
)/(8
R
S
)
where:
R
S
= sense resistor value in
.
V
SRH
= high-byte value of battery current
V
SRL
= low-byte value of battery current
The bq2014H indicates an average discharge current
with a “1” in the MSB position of the VSRH register. To
calculate discharge current, use the 2’s complement if
the concatenated register contents in the above equa-
tion.
Discharge Count Register (DCR)
The DCR register (address = 18h) stores the high-byte of
the discharge count. DCR is reset to zero at the start of
a valid discharge cycle and can count to a maximum of
FFh. DCR will not increment if EDV1 = 1 and will not
roll over from FFh.
Program Pin Full Count (PPFC)
The PPFC register contains information concerning the
program pin configuration. This information is used to
determine the data integrity of the bq2014H.
The only
approved user application for this register is to
write a zero to this register as part of a reset re-
quest.
The recommended reset method for the bq2014H is
I
Write PPFC to zero
I
Write LMD to zero
After these operations,a software reset will occur.
Resetting the bq2014H sets the following:
I
LMD = PFC
I
CPI, VDQ, RCAC, NACH/L, CACH/L, SAEH/L,
NMCV = 0
I
CI and BRP = 1
Voltage Offset (V
OS
) Interrupt (INTSS)
The INTSS register (address = 38h) is useful during in-
tial characterization of bq2014H designs.
bq2014H counts a charge pulse, CHGI (bit 0) will be set
to 1.
When the bq2014H counts a discharge pulse,
DCHGI (bit 3) will be set to 1. All other locations in the
INTSS register are reserved.
When the
Display
The bq2014H can directly display capacity information
using low-power LEDs. If LEDs are used, the program
pins should be resistively tied to V
CC
or V
SS
for a pro-
gram high or program low,respectively.
The bq2014H displays the battery charge state in relative
mode. In relative mode, the battery charge is represented
as a percentage of the LMD. Each LED segment repre-
sents20%oftheLMD.
The capacity display is also adjusted for the present bat-
tery temperature and discharge rate. The temperature
adjustment reflects the available capacity at a given
temperature but does not affect the NAC register. The
temperature adjustments are detailed in the CACT and
CACD register descriptions.
When DISP is tied to V
CC
, the SEG
1–5
outputs are inac-
tive. When DISP is left floating, the display becomes ac-
tive whenever the bq2014H detects a charge in progress
V
SRO
> V
SRQ
. When pulled low, the segment outputs be-
come active for a period of four seconds,
±
0.5 seconds.
The segment outputs are modulated as two banks, with
segments 1, 3, and 5 alternating with segments 2 and 4.
The segment outputs are modulated at approximately
100Hz with each segment bank active for 30% of the pe-
riod.
SEG
1
blinks at a 4Hz rate whenever V
SB
has been de-
tected to be below V
EDV1
(EDV1 = 1), indicating a low-
battery condition. V
SB
below V
EDVF
(EDVF = 1) disables
the display output.
Microregulator
A micropower source for the bq2014H can be inexpen-
sively built using a FET and an external resistor. (See
Figure 1.)
16
bq2014H
Preliminary
相關PDF資料 |
PDF描述 |
|---|---|
| bq2014 | Gas Gauge IC with External Charge Control(氣體Gauge（帶外部電荷控制）) |
| bq2040 | Gas Gauge IC With SMBus Interface(氣體Gauge芯片（帶SMBus 接口）) |
| bq2050H | Low-Cost Lithium Ion Power Gauge IC(低價格鋰離子電源氣體Gauge芯片) |
| bq2050 | Lithium Ion Power Gauge IC(鋰離子電源Gause 芯片) |
| bq2052 | Gas Gauge IC for Lithium Primary Cells(Gas Gauge 芯片（用于鋰電池）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ2014HEVM-001 | 功能描述:電源管理IC開發工具 BQ2014H Eval Kit for NiMH 10.8V RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| BQ2014HSN | 功能描述:電池管理 NiCd/NiMH Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ2014HSN-A309 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low-Cost NiCd/NiMH Gas Gauge IC |
| BQ2014HSNG4 | 功能描述:電池管理 NiCd/NiMH Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ2014HSNTR | 功能描述:電池管理 NiCd/NiMH Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。