- 您現在的位置：買賣IC網 > PDF目錄385185 > bq2010 (Benchmark Technology Group) Gas Gauge IC(Gas Gauge芯片) PDF資料下載
參數資料
| 型號： | bq2010 |
| 廠商： | Benchmark Technology Group |
| 英文描述： | Gas Gauge IC(Gas Gauge芯片) |
| 中文描述： | 氣體計IC（電量監測計芯片） |
| 文件頁數： | 9/20頁 |
| 文件大?。?/td> | 185K |
| 代理商： | BQ2010 |
the bq2010 should be pulled up by the host system or may
be left floating if the serial interface is not used.
The interface uses a command-based protocol, where the
host processor sends a command byte to the bq2010.
The command directs the bq2010 either to store the next
eight bits of data received to a register specified by the
command byte or to output the eight bits of data speci-
fied by the command byte.
The communication protocol is asynchronous return-to-
one. Command and data bytes consist of a stream of eight
bits that have a maximum transmission rate of 333
bits/sec. The least-significant bit of a command or data
byte is transmitted first. The protocol is simple enough
that it can be implemented by most host processors using
either polled or interrupt processing. Data input from the
bq2010 may be sampled using the pulse-width capture
timers available on some microcontrollers.
Communication is normally initiated by the host processor
sending a BREAK command to the bq2010. A BREAK is
detected when the DQ pin is driven to a logic-low state for
a time, t
or greater. The DQ pin should then be returned
to its normal ready-high logic state for a time, t
. The
bq2010 is now ready to receive a command from the host
processor.
The return-to-one data bit frame consists of three distinct
sections. The first section is used to start the transmission
by either the host or the bq2010 taking the DQ pin to a
logic-low state for a period, t
. The next section is the
actual data transmission, where the data should be valid
by a period, t
DSU
, after the negative edge used to start
communication. The data should be held for a period,
t
DV
, to allow the host or bq2010 to sample the data bit.
The final section is used to stop the transmission by re-
turning the DQ pin to a logic-high state by at least a peri-
od, t
, after the negative edge used to start communica-
tion. The final logic-high state should be held until a peri-
od, t
, to allow time to ensure that the bit transmission
was stopped properly.
The timings for data and break
communication are given in the serial communication tim-
ing specification and illustration sections.
Communication with the bq2010 is always performed
with the least-significant bit being transmitted first.
Figure 3 shows an example of a communication se-
quence to read the bq2010 NAC register.
bq2010 Registers
The bq2010 command and status registers are listed in
Table 6 and described below.
Command Register (CMDR)
The write-only CMDR register is accessed when eight
valid command bits have been received by the bq2010.
The CMDR register contains two fields:
W/R bit
Command address
The W/R bit of the command register is used to select
whether the received command is for a read or a write
function.
9
bq2010
TD201001.eps
DQ
Break
0 0 0 0 0 0
1 0 1 0 0 1
Written by Host to bq2010
CMDR = 03h
Received by Host to bq2010
NAC = 65h
LSB
MSB
LSB
MSB
1
1
1 0
Figure 3. Typical Communication with the bq2010
Symbol
V
OS
Parameter
Typical
±
50
Maximum
±
150
Units
μ
V
Notes
Offset referred to V
SR
Integrated non-linearity
error
DISP = V
CC
.
Add 0.1% per °C above or below 25°C
and 1% per volt above or below 4.25V.
INL
±
2
±
4
%
INR
Integrated non-
repeatability error
±
1
±
2
%
Measurement repeatability given
similar operating conditions.
Table 5. bq2010 Current-Sensing Errors
相關PDF資料 |
PDF描述 |
|---|---|
| bq2011K | Gas Gauge IC for High Discharge Rates(用于高放電率的氣體Gauge芯片) |
| bq2011 | Gas Gauge IC for High Discharge Rates(用于高放電率的氣體Gauge芯片) |
| bq2012 | Gas Gauge IC With Slow-Charge Control(Gas Gauge芯片（帶慢充電控制）) |
| bq2013H | Gas Gauge IC for Power-Assist Applications(應用于電源援助的氣體Gauge芯片) |
| bq2014H | Low-Cost NiCd/NiMH Gas Gauge IC(低價格NiCd/NiMHGas Gauge芯片) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ2010PN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Battery Management |
| BQ2010PN-N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Battery Management |
| BQ2010SN- | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Gas Gauge IC |
| BQ2010SN-D107 | 功能描述:電池管理 NiCd/NiMH Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ2010SN-D107 | 制造商:Texas Instruments 功能描述:IC's |
發布緊急采購，3分鐘左右您將得到回復。