參數資料
型號： bq2010
廠商： Benchmark Technology Group
英文描述： Gas Gauge IC(Gas Gauge芯片)
中文描述： 氣體計IC（電量監測計芯片）
文件頁數： 7/20頁
文件大?。?/td> 185K
代理商： BQ2010
3.
Nominal Available Charge (NAC):
NAC counts up during charge to a maximum
value of LMD and down during discharge and
self-discharge to 0. NAC is reset to 0 on initializa-
tion (PROG
= Z or low) and on the first valid charge
following discharge to EDV1. NAC is set to PFC on
initialization if PROG
= high. To prevent over-
statement of charge during periods of overcharge,
NAC stops incrementing when NAC = LMD.
4.
Discharge Count Register (DCR):
The DCR counts up during discharge independent
of NAC and could continue increasing after NAC
has decremented to 0.
Prior to NAC = 0 (empty
battery), both discharge and self-discharge in-
crement the DCR. After NAC = 0, only discharge
increments the DCR. The DCR resets to 0 when
NAC = LMD. The DCR does not roll over but stops
counting when it reaches ffffh.
The DCR value becomes the new LMD value on the
first charge after a valid discharge to V
EDV1
if:
No valid charge initiations (charges greater than
256 NAC counts, where V
> V
) occurred
during the period between NAC = LMD and EDV1
detected.
The self-discharge count is not more than 4096
counts (8% to 18% of PFC, specific percentage
threshold determined by PFC).
The temperature is
≥
0°C when the EDV1 level is
reached during discharge.
The valid discharge flag (VDQ) indicates whether
the present discharge is valid for LMD update.
Charge Counting
Charge activity is detected based on a positive voltage on
the V
input. If charge activity is detected, the bq2010
increments NAC at a rate proportional to V
and, if en-
abled, activates an LED display if the rate is equivalent to
V
> 4mV.
Charge actions increment the NAC after
compensation for charge rate and temperature.
The bq2010 determines charge activity sustained at a
continuous rate equivalent to V
> V
. A valid
charge equates to sustained charge activity greater than
256 NAC counts. Once a valid charge is detected, charge
counting continues until V
(V
+ V
) falls below
V
. V
is a programmable threshold as described in
the Digital Magnitude Filter section. The default value
for V
SRQ
is 375
μ
V.
Discharge Counting
All discharge counts where V
< V
cause the NAC
register to decrement and the DCR to increment. Ex-
ceeding the fast discharge threshold (FDQ) if the rate is
equivalent to V
< -4mV activates the display, if en-
abled.
The display becomes inactive after V
rises
above -4mV. V
is a programmable threshold as
described in the Digital Magnitude Filter section. The
default value for V
SRD
is -300
μ
V.
Self-Discharge Estimation
The bq2010 continuously decrements NAC and incre-
ments DCR for self-discharge based on time and tempera-
ture. The self-discharge count rate is programmed to be a
nominal
164
*NAC,
147
*NAC per day, or disabled as se-
lected by PROG
.
This is the rate for a battery whose
temperature is between 20°–30°C. The NAC register can-
not be decremented below 0.
Count Compensations
The bq2010 determines fast charge when the NAC up-
dates at a rate of
≥
2 counts/sec. Charge and discharge
activity is compensated for temperature and charge/dis-
charge rate before updating the NAC and/or DCR. Self-
discharge estimation is compensated for temperature
before updating the NAC or DCR.
Charge Compensation
Two charge efficiency compensation factors are used for
trickle charge and fast charge. Fast charge is defined as
a rate of charge resulting in
≥
2 NAC counts/sec (
≥
0.15C
to 0.32C depending on PFC selections; see Table 2). The
compensation defaults to the fast charge factor until the
actual charge rate is determined.
Temperature adapts the charge rate compensation factors
over three ranges between nominal, warm, and hot tem-
peratures. Thecompensationfactorsareshownbelow.
Discharge Compensation
Corrections for the rate of discharge are made by adjust-
ing an internal discharge compensation factor. The dis-
charge compensation factor is based on the namically
measured V
SR
.
7
bq2010
Charge
Temperature
Trickle Charge
Compensation
Fast Charge
Compensation
<30°C
0.80
0.95
30–40°C
0.75
0.90
> 40°C
0.65
0.80
相關PDF資料
PDF描述
bq2011K Gas Gauge IC for High Discharge Rates(用于高放電率的氣體Gauge芯片)
bq2011 Gas Gauge IC for High Discharge Rates(用于高放電率的氣體Gauge芯片)
bq2012 Gas Gauge IC With Slow-Charge Control(Gas Gauge芯片（帶慢充電控制）)
bq2013H Gas Gauge IC for Power-Assist Applications(應用于電源援助的氣體Gauge芯片)
bq2014H Low-Cost NiCd/NiMH Gas Gauge IC(低價格NiCd/NiMHGas Gauge芯片)
相關代理商/技術參數
參數描述
BQ2010PN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Battery Management
BQ2010PN-N 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Battery Management
BQ2010SN- 制造商:TI 制造商全稱:Texas Instruments 功能描述:Gas Gauge IC
BQ2010SN-D107 功能描述:電池管理 NiCd/NiMH Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
BQ2010SN-D107 制造商:Texas Instruments 功能描述:IC's
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*