- 您現在的位置：買賣IC網 > PDF目錄357616 > BH29NB1WHFV 2.9 V FIXED POSITIVE REGULATOR, PDSO5 PDF資料下載
參數資料
| 型號： | BH29NB1WHFV |
| 元件分類： | 固定正電壓單路輸出標準穩壓器 |
| 英文描述： | 2.9 V FIXED POSITIVE REGULATOR, PDSO5 |
| 封裝： | PLASTIC, HVSOF-5 |
| 文件頁數： | 6/9頁 |
| 文件大?。?/td> | 297K |
| 代理商： | BH29NB1WHFV |
Technical Note
BH
□□
NB1WHFV series
6/8
www.rohm.com
2011 ROHM Co., Ltd. All rights reserved.
2011.01 - Rev.B
●
Output capacitors
Mounting input capacitor between input pin and GND(as close to pin as possible), and also output capacitor between output
pin and GND(as close to pin as possible) is recommended. The input capacitor reduces the output impedance of the voltage
supply source connected to the VCC. The higher value the output capacitor goes, the more stable the whole operation
becomes. This leads to high load transient response. Please confirm the whole operation on actual application board.
Generally, ceramic capacitor has wide range of tolerance, temperature coefficient, and DC bias characteristic. And also its
value goes lower as time progresses. Please choose ceramic capacitors after obtaining more detailed data by asking
capacitor makers.
BH
□□
NB1WHFV
●
Operation Notes
1. Absolute maximum ratings
An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc.,
can break down the devices, thus making impossible to identify breaking mode, such as a short circuit or an open circuit.
If any over rated values will expect to exceed the absolute maximum ratings, consider adding circuit protection devices,
such as fuses.
2. Thermal design
Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating
conditions.
3. Inter-pin shorts and mounting errors
Use caution when positioning the IC for mounting on printed circuit boards. The IC may be damaged if there is any
connection error or if pins are shorted together.
4. Thermal shutdown circuit (TSD)
The IC incorporates a built-in thermal shutdown circuit (TSD circuit). The thermal shutdown circuit is designed only to
shut the IC off to prevent runaway thermal operation. It is not designed to protect the IC or guarantee its operation. Do
not continue to use the IC after operating this circuit or use the IC in an environment where the operation of this circuit is
assumed.
5. Overcurrent protection circuit
The IC incorporates a built-in overcurrent protection circuit that operates according to the output current capacity. This
circuit serves to protect the IC from damage when the load is shorted. The protection circuit is designed to limit current
flow by not latching in the event of a large and instantaneous current flow originating from a large capacitor or other
component. These protection circuits are effective in preventing damage due to sudden and unexpected accidents.
However, the IC should not be used in applications characterized by the continuous operation or transitioning of the
protection circuits. At the time of thermal designing, keep in mind that the current capability has negative characteristics
to temperatures.
6. Action in strong electromagnetic field
Use caution when using the IC in the presence of a strong electromagnetic field as doing so may cause the IC to
malfunction.
7. Ground wiring pattern
When using both small signal and large current GND patterns, it is recommended to isolate the two ground patterns,
placing a single ground point at the ground potential of application so that the pattern wiring resistance and voltage
variations caused by large currents do not cause variations in the small signal ground voltage. Be careful not to change
the GND wiring pattern of any external components, either.
0.01
0.1
1
10
100
0
50
100
150
Output Current I
OUT
[mA]
E
]
Stable region
Fig.30 Stable Operation Region (Example)
C
OUT
= 2.2 μF
Ta = +25°C
相關PDF資料 |
PDF描述 |
|---|---|
| BH30PB1WHFV | 3 V FIXED POSITIVE REGULATOR, PDSO5 |
| BH33PB1WHFV | 3.3 V FIXED POSITIVE REGULATOR, PDSO5 |
| BISC-500-100 | INTERCONNECTION DEVICE |
| BISF-504-50 | INTERCONNECTION DEVICE |
| BISF-502-75 | INTERCONNECTION DEVICE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BH29NB1WHFV-TR | 功能描述:低壓差穩壓器 - LDO 150MA 2.9V CMOS LDO Regulator RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| BH29NB1WHFWHFV | 制造商:ROHM 制造商全稱:Rohm 功能描述:1ch 150mA CMOS LDO Regulators |
| BH29NB1WHFWHFV-TR | 制造商:ROHM 制造商全稱:Rohm 功能描述:1ch 150mA CMOS LDO Regulators |
| BH29PB1WHFV | 制造商:ROHM 制造商全稱:Rohm 功能描述:1ch 150mA CMOS LDO Regulators |
| BH29PB1WHFV-TR | 功能描述:低壓差穩壓器 - LDO 2.9V CMOS LDO Regulator RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。