- 您現在的位置：買賣IC網 > PDF目錄3860 > ATTINY15L-1SC (Atmel)IC AVR MCU 1K FLASH 2.7V SO8 PDF資料下載
參數資料
| 型號： | ATTINY15L-1SC |
| 廠商： | Atmel |
| 文件頁數： | 11/85頁 |
| 文件大小： | 0K |
| 描述： | IC AVR MCU 1K FLASH 2.7V SO8 |
| 標準包裝： | 95 |
| 系列： | AVR® ATtiny |
| 核心處理器： | AVR |
| 芯體尺寸： | 8-位 |
| 速度： | 1.6MHz |
| 外圍設備： | 欠壓檢測/復位，POR，PWM，WDT |
| 輸入/輸出數： | 6 |
| 程序存儲器容量： | 1KB（512 x 16） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大小： | 64 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 數據轉換器： | A/D 4x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 8-SOIC（0.209"，5.30mm 寬） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
19
ATtiny15L
1187H–AVR–09/07
Interrupt Handling
The ATtiny15L has two 8-bit Interrupt Mask Control Registers: GIMSK (General Inter-
rupt Mask Register) and TIMSK (Timer/Counter Interrupt Mask Register).
When an interrupt occurs, the Global Interrupt Enable I-bit is cleared (zero) and all inter-
rupts are disabled. The user software can set the I-bit (one) to enable interrupts. The I-
bit is set (one) when a Return from Interrupt instruction (RETI) is executed.
When the Program Counter is vectored to the actual Interrupt Vector in order to execute
the interrupt handling routine, hardware clears the corresponding flag that generated the
interrupt. Some of the interrupt flags can also be cleared by writing a logical “1” to the
flag bit position(s) to be cleared.
If an interrupt condition occurs when the corresponding interrupt enable bit is cleared
(zero), the interrupt flag will be set and remembered until the interrupt is enabled, or the
flag is cleared by software.
If one or more interrupt conditions occur when the global interrupt enable bit is cleared
(zero), the corresponding interrupt flag(s) will be set and remembered until the global
interrupt enable bit is set (one), and will be executed by order of priority.
Note that external level interrupt does not have a flag, and will only be remembered for
as long as the interrupt condition is present.
Note that the Status Register is not automatically stored when entering an interrupt rou-
tine and restored when returning from an interrupt routine. This must be handled by
software.
Interrupt Response Time
The interrupt execution response for all the enabled AVR interrupts is four clock cycles
minimum. After the four clock cycles the Program Vector address for the actual interrupt
handling routine is executed. During this 4-clock-cycle period, the Program Counter
(nine bits) is pushed onto the Stack. The vector is often a relative jump to the interrupt
routine, and this jump takes two clock cycles. If an interrupt occurs during execution of a
multi-cycle instruction, this instruction is completed before the interrupt is served. If an
interrupt occurs when the MCU is in sleep mode, the interrupt execution response time
is increased by four clock cycles.
A return from an interrupt handling routine takes four clock cycles. During these four
clock cycles, the Program Counter (nine bits) is popped back from the Stack. When
AVR exits from an interrupt, it will always return to the main program and execute one
more instruction before any pending interrupt is served.
The General Interrupt Mask
Register – GIMSK
Bit 7 – Res: Reserved Bit
This bit is a reserved bit in the ATtiny15L and always reads as zero.
Bit 6 – INT0: External Interrupt Request 0 Enable
When the INT0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one),
the external pin interrupt is activated. The Interrupt Sense Control0 bits 1/0 (ISC01 and
ISC00) in the MCU general Control Register (MCUCR) define whether the external
interrupt is activated on rising or falling edge, on pin change, or low level of the INT0 pin.
Activity on the pin will cause an interrupt request even if INT0 is configured as an output.
Bit
7
65
43
2
1
0
$3B
–
INT0
PCIE
–
GIMSK
Read/Write
R
R/W
R
Initial Value
0
相關PDF資料 |
PDF描述 |
|---|---|
| ATTINY15L-1PI | IC AVR MCU 1K FLASH 2.7V 8DIP |
| ATTINY15L-1PC | IC AVR MCU 1K FLASH 2.7V 8DIP |
| AT89C2051-24SI | MICRO CONTROLLER |
| AT90S8515-8JC | IC MCU 8K FLSH 8MHZ 44PLCC |
| PIC24FV16KA304-I/PT | MCU 16KB FLASH 2KB RAM 44-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATTINY15L-1SC SL383 | 制造商:Atmel Corporation 功能描述:MCU 8-Bit ATtiny AVR RISC 1KB Flash 3.3V/5V 8-Pin SOIC EIAJ T/R |
| ATTINY15L-1SI | 功能描述:8位微控制器 -MCU AVR 1K FLASH 64B EE ADC 3V 1.6MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ATTINY15L-1SI SL383 | 制造商:Atmel Corporation 功能描述:MCU 8-bit ATtiny AVR RISC 1KB Flash 3.3V/5V 8-Pin SOIC EIAJ T/R |
| ATTINY15L-1SITRSL#QS309 | 制造商:Atmel Corporation 功能描述:ATLATTINY15L-1SITRSL#QS309 PGMD FOR AAPL |
| ATTINY15L-1SU | 功能描述:8位微控制器 -MCU AVR 1K FLASH 64B EE ADC 3V 1.6MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。