參數資料
型號： ATSAM3S-EK2
廠商： Atmel
文件頁數： 9/57頁
文件大?。?/td> 0K
描述： EVAL KIT FOR SAM3S8 & SAM3SD8
設計資源： SAM3S-EK2 Design & Mfg Files
SAM3S-EK2 Design & Mfg Files Information
SAM3S-EK2 Demo Release Notes
標準包裝： 1
類型： MCU
適用于相關產品： ATSAM3S 系列
所含物品： 板
17
11090BS–ATARM–22-Oct-13
SAM3S8/SD8 Summary
Supply Monitor alarm
RTC alarm
RTT alarm
5.5.2
Wait Mode
The purpose of the wait mode is to achieve very low power consumption while maintaining the
whole device in a powered state for a startup time of less than 10 s. Current Consumption in
Wait mode is typically 15 A (total current consumption) if the internal voltage regulator is used
or 8 A if an external regulator is used.
In this mode, the clocks of the core, peripherals and memories are stopped. However, the core,
peripherals and memories power supplies are still powered. From this mode, a fast start up is
available.
This mode is entered via Wait for Event (WFE) instructions with LPM = 1 (Low Power Mode bit in
PMC_FSMR). The Cortex-M3 is able to handle external events or internal events in order to
wake-up the core (WFE). This is done by configuring the external lines WUP0-15 as fast startup
wake-up pins (refer to Section 5.7 “Fast Startup”). RTC or RTT Alarm and USB wake-up events
can be used to wake up the CPU (exit from WFE).
Entering Wait Mode:
Select the 4/8/12 MHz fast RC oscillator as Main Clock
Set the LPM bit in the PMC Fast Startup Mode Register (PMC_FSMR)
Execute the Wait-For-Event (WFE) instruction of the processor
Note:
Internal Main clock resynchronization cycles are necessary between the writing of MOSCRCEN
bit and the effective entry in Wait mode. Depending on the user application, waiting for
MOSCRCEN bit to be cleared is recommended to ensure that the core will not execute undesired
instructions.
5.5.3
Sleep Mode
The purpose of sleep mode is to optimize power consumption of the device versus response
time. In this mode, only the core clock is stopped. The peripheral clocks can be enabled. The
current consumption in this mode is application dependent.
This mode is entered via Wait for Interrupt (WFI) or Wait for Event (WFE) instructions with
LPM = 0 in PMC_FSMR.
The processor can be awakened from an interrupt if WFI instruction of the Cortex M3 is used, or
from an event if the WFE instruction is used to enter this mode.
相關PDF資料
PDF描述
AIUR-06-152K INDUCTOR POWER 1500UH 10% T/H
V300C3V3C50BL3 CONVERTER MOD DC/DC 3.3V 50W
MCP73861T-I/SLG IC CONTROLLER LI-ION 4.1V 16SOIC
AIUR-06-122K INDUCTOR POWER 1200UH 10% T/H
V300C3V3C50B3 CONVERTER MOD DC/DC 3.3V 50W
相關代理商/技術參數
參數描述
ATSAM3U 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:AT91 ARM Thumb-based Microcontrollers
ATSAM3U_10 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:AT91ARM Cortex M3-based Microcontrollers
ATSAM3U1CA-AU 功能描述:ARM微控制器 - MCU 64K Flash, 20K SRAM 32-bit ARM Cortex M3 RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
ATSAM3U1CA-CU 功能描述:ARM微控制器 - MCU 64K Flash, 20K SRAM 32-bit ARM Cortex M3 RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
ATSAM3U1CB-AU 功能描述:ARM微控制器 - MCU LQFP, Grn, IT, MRL B RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*