- 您現在的位置：買賣IC網 > PDF目錄375377 > ATS635LSE (Allegro MicroSystems, Inc.) Programmable Back Biased Hall-Effect Switch with TPOS Functionality PDF資料下載
參數資料
| 型號： | ATS635LSE |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | Programmable Back Biased Hall-Effect Switch with TPOS Functionality |
| 中文描述： | 可編程回到偏霍爾效應的聚烯烴功能開關 |
| 文件頁數： | 6/15頁 |
| 文件大小： | 814K |
| 代理商： | ATS635LSE |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
ATS635LSE and ATS636LSE
PROGRAMMABLE TRUE POWER-ON HALL-EFFECT GEAR-TOOTH SWITCHES
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
Copyright 2005 Allegro MicroSystems, Inc.
Regulator
Amplifier
Sample/
Hold
CLOCK
Hall Element
FUNCTIONAL
DESCRIPTION
Chopper-Stabilized Technique
.
The basic Hall sensor
is a small sheet of semiconductor material in which a
constant bias current will flow when a constant voltage
source is applied. The output will take the form of a
voltage measured across the width of the sheet and will
have negligible value in the absence of a magnetic field.
When a magnetic field with flux lines at right angles to
the Hall current is applied, a small signal voltage directly
proportional to the strength of the magnetic field will
occur at the output terminals.
This signal voltage is proportionally small relative to the
offset produced at the input of the chip. This makes it
very difficult to process the signal and maintain an
accurate, reliable output over the specified temperature
and voltage range. Therefore, it is important to reduce
any offset on the signal that could be amplified when the
signal is processed.
Chopper Stabilization is a unique approach used to
minimize input offset on the chip. This technique
removes a key source of output drift with temperature
and stress, and produces a 3X reduction in offset over
other conventional methods.
This offset reduction Chopping Technique is based on a
signal modulation-demodulation process. The undesired
offset signal is separated from the magnetically induced
signal in the frequency domain. The offset (and any low
frequency noise) component of the signal can be seen
as signal corruption added after the signal modulation
process has taken place. Therefore, the DC offset is not
modulated and remains a low frequency component.
Consequently, the signal demodulation process acts as
a modulation process for the offset causing the
magnetically induced signal to recover its original
spectrum at baseband while the DC offset becomes a
high frequency signal. Then, using a low pass filter the
signal passes while the modulated DC offset is
suppressed.
The advantage of this approach is significant offset
reduction, which de-sensitizes the chip against the
effects of temperature and stress. The disadvantage is
that this technique features a demodulator that uses a
sample and hold block to store and recover the signal.
This sampling process can slightly degrade the Signal-
to-Noise Ratio (SNR) by producing replicas of the noise
spectrum at the baseband. The degradation is a
function of the ratio between the white noise spectrum
and the sampling frequency. The effect of the
degradation of the SNR is higher jitter, a.k.a. signal
repeatability. In comparison to a continuous time device,
the jitter spec can be increased by a factor of five.
Figure 1 – Concept of Chopper-Stabilization Algorithm
相關PDF資料 |
PDF描述 |
|---|---|
| ATS635LSETN-T | Programmable Back Biased Hall-Effect Switch with TPOS Functionality |
| ATS636LSETN-T | RESISTOR, FIXED, FILM, CHIP |
| ATS640JSB | True Zero-Speed,Self-Calibrating ,Hall-Effect Gear-Tooth Sensor For Two-Wire Applications(真速度歸零，自校準，霍爾效應齒輪嚙合傳感器（用于2線）) |
| ATS642LSH | Two-Wire True Zero Speed Miniature Differential Peak-Detecting Gear Tooth Sensor with Continuous Calibration |
| ATS642LSHTN-I1-T | Two-Wire True Zero Speed Miniature Differential Peak-Detecting Gear Tooth Sensor with Continuous Calibration |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATS635LSETN | 功能描述:IC SENSOR GEAR TOOTH 4-SIP RoHS:否 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| ATS635LSETN-T | 功能描述:IC SENSOR GEAR TOOTH 4-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| ATS636LSB-FP | 功能描述:IC SENSOR GEAR TOOTH 4-SIP RoHS:否 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| ATS636LSE | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Programmable Back Biased Hall-Effect Switch with TPOS Functionality |
| ATS636LSE_12 | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:The ATS636LSE programmable, true power-on state (TPOS), device is optimized Hall-effect IC and rare-earth pellet combinations that switch in response to magnetic signals... |
發布緊急采購，3分鐘左右您將得到回復。