參數資料
型號： AT90S8535-8PI
廠商： Atmel
文件頁數： 50/127頁
文件大小： 0K
描述： IC MCU 8K FLSH 8MHZ A/D IT 40DIP
標準包裝： 18
系列： AVR® 90S
核心處理器： AVR
芯體尺寸： 8-位
速度： 8MHz
連通性： SPI，UART/USART
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 32
程序存儲器容量： 8KB（4K x 16）
程序存儲器類型： 閃存
EEPROM 大小： 512 x 8
RAM 容量： 512 x 8
電壓 - 電源 (Vcc/Vdd)： 4 V ~ 6 V
數據轉換器： A/D 8x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 40-DIP（0.600"，15.24mm）
包裝： 管件
29
AT90S/LS8535
1041H–11/01
Interrupt Response Time
The interrupt execution response for all the enabled AVR interrupts is four clock cycles
minimum. Four clock cycles after the interrupt flag has been set, the program vector
address for the actual interrupt handling routine is executed. During this 4-clock-cycle
period, the Program Counter (2 bytes) is pushed onto the stack and the Stack Pointer is
decremented by 2. The vector is normally a relative jump to the interrupt routine and this
jump takes two clock cycles. If an interrupt occurs during execution of a multi-cycle
instruction, this instruction is completed before the interrupt is served.
A return from an interrupt handling routine (same as for a subroutine call routine) takes
four clock cycles. During these four clock cycles, the Program Counter (2 bytes) is
popped back from the stack, the Stack Pointer is incremented by 2 and the I-flag in
SREG is set. When the AVR exits from an interrupt, it will always return to the main pro-
gram and execute one more instruction before any pending interrupt is served.
MCU Control Register –
MCUCR
The MCU Control Register contains control bits for general MCU functions.
Bit 7 – Res: Reserved Bit
This bit is a reserved bit in the AT90S8535 and always reads zero.
Bit 6 – SE: Sleep Enable
The SE bit must be set (one) to make the MCU enter the Sleep Mode when the SLEEP
instruction is executed. To avoid the MCU entering the Sleep Mode unless it is the pro-
grammer’s purpose, it is recommended to set the Sleep Enable (SE) bit just before the
execution of the SLEEP instruction.
Bits 5, 4 – SM1/SM0: Sleep Mode Select Bits 1 and 0
These bits select between the three available sleep modes as shown in Table 7.
Bits 3, 2 – ISC11, ISC10: Interrupt Sense Control 1 Bits 1 and 0
The External Interrupt 1 is activated by the external pin INT1 if the SREG I-flag and the
corresponding interrupt mask in the GIMSK is set. The level and edges on the external
INT1 pin that activate the interrupt are defined in Table 8.
Bit
765
432
10
$35 ($55)
–
SE
SM1
SM0
ISC11
ISC10
ISC01
ISC00
MCUCR
Read/Write
R
R/W
Initial Value
0
Table 7. Sleep Mode Select
SM1
SM0
Sleep Mode
00
Idle
01
Reserved
1
0
Power-down
11
Power Save
相關PDF資料
PDF描述
AT90USB1287-16AUR IC MCU AVR 128K ISP USB TQFP64
AT90USB162-16AUR IC AVR MCU 16K FLASH 32TQFP
AT91FR40162SB-CU-999 IC MCU 32BIT RISC 121BGA
AT91M40800-33AI SL383 IC ARM MCU 16BIT 100TQFP
AT91M42800A-33CJ IC ARM7 MCU 144 BGA
相關代理商/技術參數
參數描述
AT90SA7-MLTU 功能描述:程序設計器 - 基于通用和內存 ASICS RoHS:否 制造商:Xeltek 產品:Universal Device Programmers 工具用于評估:EPROM, Parallel/Serial EEPROM, FPGA, PROM, Flash, BPROM, MCUs, PLD Devices 接口類型:Parallel, USB 工作電源電壓:90 VAC to 250 VAC
AT90SC12036RU 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Secure Microcontroller for Smart Cards
AT90SC128112RU 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Secure Microcontroller for Smart Cards
AT90SC12836RCFT 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Secure Microcontrollers for Smart Cards
AT90SC12836RCFT_07 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Secure Microcontrollers for Smart Cards
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*