參數資料
型號： AT89C51RB2-3CSUM
廠商： Atmel
文件頁數： 99/127頁
文件大?。?/td> 0K
描述： IC 8051 MCU 16K FLASH 40-DIP
產品培訓模塊： MCU Product Line Introduction
標準包裝： 216
系列： 89C
核心處理器： 8051
芯體尺寸： 8-位
速度： 60MHz
連通性： SPI，UART/USART
外圍設備： POR，PWM，WDT
輸入/輸出數： 32
程序存儲器容量： 16KB（16K x 8）
程序存儲器類型： 閃存
RAM 容量： 1.25K x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 5.5 V
振蕩器型： 外部
工作溫度： -40°C ~ 85°C
封裝/外殼： 40-DIP（0.600"，15.24mm）
包裝： 管件
配用： AT89OCD-01-ND - USB EMULATOR FOR AT8XC51 MCU
AT89STK-11-ND - KIT STARTER FOR AT89C51RX2
73
AT89C51RB2/RC2
4180E–8051–10/06
Error Conditions
The following flags in the SPSTA signal SPI error conditions:
Mode Fault (MODF)
Mode Fault error in Master mode SPI indicates that the level on the Slave Select (SS)
pin is inconsistent with the actual mode of the device. MODF is set to warn that there
may be a multi-master conflict for system control. In this case, the SPI system is
affected in the following ways:
An SPI receiver/error CPU interrupt request is generated
The SPEN bit in SPCON is cleared. This disables the SPI
The MSTR bit in SPCON is cleared
When SS Disable (SSDIS) bit in the SPCON register is cleared, the MODF flag is set
when the SS signal becomes ’0’.
However, as stated before, for a system with one Master, if the SS pin of the Master
device is pulled low, there is no way that another Master attempts to drive the network.
In this case, to prevent the MODF flag from being set, software can set the SSDIS bit in
the SPCON register and therefore making the SS pin as a general-purpose I/O pin.
Clearing the MODF bit is accomplished by a read of SPSTA register with MODF bit set,
followed by a write to the SPCON register. SPEN Control bit may be restored to its orig-
inal set state after the MODF bit has been cleared.
Write Collision (WCOL)
A Write Collision (WCOL) flag in the SPSTA is set when a write to the SPDAT register is
done during a transmit sequence.
WCOL does not cause an interruption, and the transfer continues uninterrupted.
Clearing the WCOL bit is done through a software sequence of an access to SPSTA
and an access to SPDAT.
Overrun Condition
An overrun condition occurs when the Master device tries to send several data Bytes
and the Slave devise has not cleared the SPIF bit issuing from the previous data Byte
transmitted. In this case, the receiver buffer contains the Byte sent after the SPIF bit was
last cleared. A read of the SPDAT returns this Byte. All others Bytes are lost.
This condition is not detected by the SPI peripheral.
SS Error Flag (SSERR)
A Synchronous Serial Slave Error occurs when SS goes high before the end of a
received data in slave mode. SSERR does not cause in interruption, this bit is cleared
by writing 0 to SPEN bit (reset of the SPI state machine).
Interrupts
Two SPI status flags can generate a CPU interrupt requests:
Table 55. SPI Interrupts
Serial Peripheral data transfer flag, SPIF: This bit is set by hardware when a transfer
has been completed. SPIF bit generates transmitter CPU interrupt requests.
Mode Fault flag, MODF: This bit becomes set to indicate that the level on the SS is
inconsistent with the mode of the SPI. MODF with SSDIS reset, generates receiver/error
CPU interrupt requests. When SSDIS is set, no MODF interrupt request is generated.
Figure 31 gives a logical view of the above statements.
Flag
Request
SPIF (SP data transfer)
SPI Transmitter Interrupt request
MODF (Mode Fault)
SPI Receiver/Error Interrupt Request (if SSDIS = ’0’)
相關PDF資料
PDF描述
AT89C51RB2-RLTUM IC 8051 MCU FLASH 16K 44VQFP
VJ1825A152JBGAT4X CAP CER 1500PF 1KV 5% NP0 1825
AT89C51RB2-SLSUM IC 8051 MCU FLASH 16K 44PLCC
VJ1825A152JBLAT4X CAP CER 1500PF 630V 5% NP0 1825
VJ1825A152KBEAT4X CAP CER 1500PF 500V 10% NP0 1825
相關代理商/技術參數
參數描述
AT89C51RB2L1-RLTUL 功能描述:8位微控制器 -MCU Microcontroller RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89C51RB2-RLRIL 功能描述:IC MCU FLASH 8051 16K 3V 44-VQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:89C 標準包裝:1,500 系列:AVR® ATtiny 核心處理器:AVR 芯體尺寸:8-位 速度:16MHz 連通性:I²C，LIN，SPI，UART/USART，USI 外圍設備:欠壓檢測/復位，POR，PWM，溫度傳感器，WDT 輸入/輸出數:16 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:512 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:帶卷 (TR)
AT89C51RB2-RLRIM 功能描述:IC MCU FLASH 8051 16K 5V 44-VQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:89C 產品培訓模塊:MCU Product Line Introduction AVR® UC3 Introduction 標準包裝:2,500 系列:AVR®32 UC3 B 核心處理器:AVR 芯體尺寸:32-位 速度:60MHz 連通性:I²C，IrDA，SPI，SSC，UART/USART，USB 外圍設備:欠壓檢測/復位，DMA，POR，PWM，WDT 輸入/輸出數:28 程序存儲器容量:128KB（128K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:32K x 8 電壓 - 電源 (Vcc/Vdd):1.65 V ~ 1.95 V 數據轉換器:A/D 6x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TQFP 包裝:帶卷 (TR) 配用:ATSTK600-TQFP48-ND - STK600 SOCKET/ADAPTER 48-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATEVK1101-ND - KIT DEV/EVAL FOR AVR32 AT32UC3B 其它名稱:AT32UC3B1128-AUR-NDAT32UC3B1128-AURTR
AT89C51RB2-RLRUL 功能描述:8位微控制器 -MCU C51RB2 FLASH 3V 16k ind RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89C51RB2-RLRUM 功能描述:8位微控制器 -MCU C51RB2 FLASH 5V 16k ind RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*