參數資料
型號: AT89C5131A-PUTIM
廠商: Atmel
文件頁數: 27/176頁
文件大?。?/td> 0K
描述: IC 8051 MCU FLASH 32K USB 32QFN
標準包裝: 260
系列: AT89C513x
核心處理器: C52X2
芯體尺寸: 8-位
速度: 48MHz
連通性: I²C,SPI,UART/USART,USB
外圍設備: LED,POR,PWM,WDT
輸入/輸出數: 18
程序存儲器容量: 32KB(32K x 8)
程序存儲器類型: 閃存
EEPROM 大?。?/td> 4K x 8
RAM 容量: 1.25K x 8
電壓 - 電源 (Vcc/Vdd): 2.7 V ~ 5.5 V
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 32-VQFN 裸露焊盤
包裝: 托盤
配用: AT89STK-10-ND - KIT EVAL APPL MASS STORAGE
AT89STK-05-ND - KIT STARTER FOR AT89C5131
120
AT89C5131
4136C–USB–04/05
Endpoint FIFO reset
Before using an endpoint, its FIFO will be reset. This action resets the FIFO pointer
to its original value, resets the byte counter of the endpoint (UBYCTLX and
UBYCTHX registers), and resets the data toggle bit (DTGL bit in UEPCONX).
The reset of an endpoint FIFO is performed by setting to 1 and resetting to 0 the
corresponding bit in the UEPRST register.
For example, in order to reset the Endpoint number 2 FIFO, write 0000 0100b then
0000 0000b in the UEPRST register.
Note that the endpoint reset doesn’t reset the bank number for ping-pong endpoints.
Read/Write Data FIFO
Read Data FIFO
The read access for each OUT endpoint is performed using the UEPDATX register.
After a new valid packet has been received on an Endpoint, the data are stored into the
FIFO and the byte counter of the endpoint is updated (UBYCTLX and UBYCTHX regis-
ters). The firmware has to store the endpoint byte counter before any access to the
endpoint FIFO. The byte counter is not updated when reading the FIFO.
To read data from an endpoint, select the correct endpoint number in UEPNUM and
read the UEPDATX register. This action automatically decreases the corresponding
address vector, and the next data is then available in the UEPDATX register.
Write Data FIFO
The write access for each IN endpoint is performed using the UEPDATX register.
To write a byte into an IN endpoint FIFO, select the correct endpoint number in UEP-
NUM and write into the UEPDATX register. The corresponding address vector is
automatically increased, and another write can be carried out.
Warning 1: The byte counter is not updated.
Warning 2: Do not write more bytes than supported by the corresponding endpoint.
FIFO Mapping
Figure 58. Endpoint FIFO Configuration
UEPNUM
Endpoint 0
Endpoint 6
UEPSTA0
UEPCON0
UEPDAT0
UEPSTA6
UEPCON6
UEPDAT6
0
1
2
3
4
5
6
SFR registers
UEPSTAX
UEPCONX
UEPDATX
X
UBYCTH0
UBYCTL0
UBYCTH6
UBYCTL6
UBYCTHX
UBYCTLX
相關PDF資料
PDF描述
AT89C5131A-TISIL IC 8051 MCU FLASH 32K USB 28SOIC
AT89C5132-RORUL MCU 8051 FLASH USB 80TQFP
AT89C51AC3-SLSIM IC 8051 MCU FLASH 64K 44PLCC
AT89C51CC03C-RLRIM IC 8051 MCU FLASH 64K 44VQFP
AT89C51ED2-SMRUM IC MCU FLASH 8051 64K 5V 68PLCC
相關代理商/技術參數
參數描述
AT89C5131A-PUTUM 功能描述:8位微控制器 -MCU C5130A 32K Flash USB RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89C5131A-RDTIL 功能描述:IC 8051 MCU FLASH 32K USB 64VQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:AT89C513x 標準包裝:9 系列:87C 核心處理器:8051 芯體尺寸:8-位 速度:40/20MHz 連通性:UART/USART 外圍設備:POR,WDT 輸入/輸出數:32 程序存儲器容量:32KB(32K x 8) 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:0°C ~ 70°C 封裝/外殼:40-DIP(0.600",15.24mm) 包裝:管件
AT89C5131A-RDTIM 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Flash Microcontroller with Full Speed USB Device
AT89C5131A-RDTUL 功能描述:8位微控制器 -MCU 32K Flash 3V USB RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89C5131A-RDTUM 功能描述:8位微控制器 -MCU C5130A 32K Flash RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT