- 您現在的位置：買賣IC網 > PDF目錄1902 > AS8501-ASOT (ams)IC CURRENT MEASURE SOLAR 16-SOIC PDF資料下載
參數資料
| 型號： | AS8501-ASOT |
| 廠商： | ams |
| 文件頁數： | 2/41頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CURRENT MEASURE SOLAR 16-SOIC |
| 標準包裝： | 1,500 |
| 類型： | 數據采集系統（DAS） |
| 輸入類型： | 模擬，數字 |
| 輸出類型： | 模擬，數字 |
| 接口： | 串行 |
| 電流 - 電源： | 5mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 16-SOIC |
| 包裝： | 帶卷 (TR) |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
AS8501 - Data Sheet
austriamicrosystems
Revision 1.1, 04-April-06
www.austriamicrosystems.com
Page 9 of 40
7
Functional Description
7.1
Power on Reset
The power on reset is iniciated during each power up of the ASSP and can be triggered purpously by reducing the analog supply voltage (VDDA) to a
value lower than Vporlo for a time interval longer than 0.5 sec.
During power on reset sequence the following steps are performed automatically:
-
The chip goes to mode MZL (see 7.4)
-
Internal clock is enabled
-
The calibration constants are loaded from Zener-zap memory to the appropriate registers (ZTR=>TRR, ZCL=>CAR). The load procedure is
directed by the internal clock and can be monitored on INTN pin. 188 clock pulses are generated from the internal oscillator source. Pulse period
is equal to internal clock period.
After the power-on reset sequence is finished:
-
the operation continues with internal clock if no external clock is detected. In this case the ASSPs switches to mode MWU with default value of
threshold register ( 214 )
-
If external clock is available the ASSP switches to mode current measurement MMS (default measurement with default configuration: gain=100,
fovs=4.096MHz, R1=64, MM=4, R2=1, NTH=214).
-
The microcontroller can communicate via SDI interface whenever appropriate, i.e. CAR and TRR register can be rewritten from the C if
necessary.
-
Because the automatic selected calibration factor (CGI4) is loaded with zeros, the ASSP delivers constant zero at the output to allow the C to
check for an unwanted POR. To bring the ASSP back into normal operation for current
measurement with gain100 the C has to copy the CAU4 content into the CGI4 factor in the CAR-register.
(see also 7.5.5 and 8.6.2)
7.2
Analog part, general description
The input signals are level shifted to AGND (+ 2.5 V) then switched by the special high quality MUX- which contains also the chopper – to the input of
the programmable gain amplifier (PGA). This low noise amplifier is optimised for best linearity, TC- value and speed at gain 24.
The systems contains an internal bandgap reference with high stability, low noise and low TC-value. The output of a programmable current source can
be switched to the analog inputs VBAT, ETS and ETR for testing the sensor connections
or for external activation of resistors, bridges or sensors (RTD, NTC). The voltage drop generated by the current is measured at the corresponding
input/output PIN.
For the wire break test of the RSHH and RSHL inputs special low noise current sources are implemented.
The integrated temperature sensor can also be switched to the PGA by the MUX and measured any time. The chip temperature can be used for the
temperature compensation of
the gain of the different channels in the external C, which increases the absolute accuracy considerably.
The offset of the amplifier itself is already fairly low, but to guarantee the full dynamic range it can be trimmed via the digital interface to nearly zero
independent of the autozero chopping function.
In the same way the manufacturing spread of the absolute value of the reference voltage can be eliminated and the TC-value set to nearly zero by a
trimming process via the SDI interface.
For more details of the input multiplexer see the following schematic. The position of all switches is defined by writing into the registers CRA, CRB and
CRG via the SDI bus, which is explained in 7.5.2 through 7.5.4.
INTERNAL
TEMPERA-
TURE
AD-
CON-
VERTER
PGA
AUXILIARY
CURRENT
SOURCE
M 12
M 13
M 3
M 10
M 14
CURRENT
SOURCE
M 2
M 1
M 4
M 15
M 8
M 7
M 9
M 6
ETR
ETS
VBAT
RSHH
RSHL
M 5
Figure 3: Multiplexer
ams
AG
Technical
content
still
valid
相關PDF資料 |
PDF描述 |
|---|---|
| AS8510-ASST | IC BATTERY MANAGEMENT 20-SSOP |
| AS8530-ASOT-002-500 | IC TXRX LIN COMPANION 8-SOIC |
| AS8530A-ASOT-500 | IC SYSTEM BASIS CHIP 8-SOIC |
| AT17F080-30TQI | IC FLASH CONFIG 8M 44TQFP |
| AT17F080A-30QI | IC FLASH CONFIG 8M 32TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AS8501-ASOU | 功能描述:IC DATA ACQ 16-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AS8501T&R | 制造商:AMSCO 制造商全稱:austriamicrosystems AG 功能描述:High precision voltage and current measurement sensor interface |
| AS8501TR | 制造商:AMSCO 制造商全稱:austriamicrosystems AG 功能描述:High precision voltage and current measurement sensor interface |
| AS8501TUB | 制造商:AMSCO 制造商全稱:austriamicrosystems AG 功能描述:High precision voltage and current measurement sensor interface |
| AS85049-32-1 | 制造商:GLENAIR 制造商全稱:Glenair, Inc. 功能描述:90° Adapter, Non-Environmental, RFI |
發布緊急采購，3分鐘左右您將得到回復。