- 您現在的位置：買賣IC網 > PDF目錄166212 > AM29F032B-150SE (SPANSION LLC) 4M X 8 FLASH 5V PROM, 150 ns, PDSO44 PDF資料下載
參數資料
| 型號： | AM29F032B-150SE |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | 4M X 8 FLASH 5V PROM, 150 ns, PDSO44 |
| 封裝： | MO-180AA, SOP-44 |
| 文件頁數： | 3/41頁 |
| 文件大?。?/td> | 1511K |
| 代理商： | AM29F032B-150SE |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
Am29F032B
11
contains timing specification tables and timing dia-
grams for write operations.
Program and Erase Operation Status
During an erase or program operation, the system
may check the status of the operation by reading the
status bits on DQ7–DQ0. Standard read cycle timings
and ICC read specifications apply. The Erase Resume
command is valid only during the Erase Suspend
mode.Refer to “Erase Suspend/Erase Resume Com-
mands” on page 17 for more information, and to each
“AC Characteristics” on page 27 section for timing dia-
grams.
Standby Mode
When the system is not reading or writing to the device,
it can place the device in the standby mode. In this
mode, current consumption is greatly reduced, and the
outputs are placed in the high impedance state, inde-
pendent of the OE# input.
The device enters the CMOS standby mode when CE#
and RESET# pins are both held at VCC ± 0.5 V. (Note
that this is a more restricted voltage range than VIH.)
The device enters the TTL standby mode when CE#
and RESET# pins are both held at VIH. The device re-
quires standard access time (tCE) for read access when
the device is in either of these standby modes, before
it is ready to read data.
The device also enters the standby mode when the RE-
SET# pin is driven low. Refer to the next section, “RE-
If the device is deselected during erasure or program-
ming, the device draws active current until the
operation is completed.
ICC3 in DC Characteristics tables, represents the
standby current specification.
RESET#: Hardware Reset Pin
The RESET# pin provides a hardware method of reset-
ting the device to reading array data. When the system
drives the RESET# pin low for at least a period of tRP,
the device immediately terminates any operation in
progress, tristates all data output pins, and ignores all
read/write attempts for the duration of the RESET#
pulse. The device also resets the internal state ma-
chine to reading array data. The operation that was in-
terrupted should be reinitiated once the device is ready
to accept another command sequence, to ensure data
integrity.
Current is reduced for the duration of the RESET#
pulse. When RESET# is held at VIL, the device enters
the TTL standby mode; if RESET# is held at VSS ±
0.5 V, the device enters the CMOS standby mode.
The RESET# pin may be tied to the system reset cir-
cuitry. A system reset would thus also reset the Flash
memory, enabling the system to read the boot-up firm-
ware from the Flash memory.
If RESET# is asserted during a program or erase oper-
ation, the RY/BY# pin remains a “0” (busy) until the in-
ternal reset operation is complete, which requires a
time of tREADY (during Embedded Algorithms). The sys-
tem can thus monitor RY/BY# to determine whether the
reset operation is complete. If RESET# is asserted
when a program or erase operation is not executing
(RY/BY# pin is “1”), the reset operation is completed
within a time of tREADY (not during Embedded Algo-
rithms). The system can read data tRH after the RE-
SET# pin returns to VIH.
Refer to the “AC Characteristics” on page 27 tables for
RESET# parameters and timing diagram.
Output Disable Mode
When the OE# input is at VIH, output from the device is
disabled. The output pins are placed in the high imped-
ance state.
相關PDF資料 |
PDF描述 |
|---|---|
| AM29F032B-75FC | 4M X 8 FLASH 5V PROM, 70 ns, PDSO40 |
| AM29F080-120SEB | 1M X 8 FLASH 5V PROM, 120 ns, PDSO44 |
| AM29F080-150EEB | 1M X 8 FLASH 5V PROM, 150 ns, PDSO40 |
| Am29F100B-120DGI | Hex Inverters 14-TSSOP -40 to 85 |
| Am29F100B-120DPC | Hex Inverters 14-TSSOP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29F032B75ED | 制造商:Advanced Micro Devices 功能描述: |
| AM29F032B-75EF | 制造商:Spansion 功能描述: 制造商:Spansion 功能描述:32M (4M X 8-BIT) 5V FLSH SCTR 制造商:Spansion 功能描述:IC, FLASH MEM, 32MBIT, 75NS, 40-TSOP, Memory Type:Flash - NOR, Memory Size:32Mbi |
| AM29F032B-75EF\\T | 制造商:Spansion 功能描述:32M (4MX8) 5V, UNIFORM SECTOR, TSOP40, IND, HAZMAT TR - Tape and Reel |
| AM29F032B-75EF\T | 制造商:Spansion 功能描述:32M (4MX8) 5V, UNIFORM SECTOR, TSOP40, IND, HAZMAT TR - Tape and Reel |
| AM29F032B-75SF | 功能描述:閃存 32M (4MX8) 75ns 5v Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。