- 您現在的位置：買賣IC網 > PDF目錄385090 > AK4183 (Asahi Kasei Microsystems Co.,Ltd) I2C Touch Screen Controller PDF資料下載
參數資料
| 型號： | AK4183 |
| 廠商： | Asahi Kasei Microsystems Co.,Ltd |
| 英文描述： | I2C Touch Screen Controller |
| 中文描述： | 觸摸屏控制器的I2C |
| 文件頁數： | 11/17頁 |
| 文件大?。?/td> | 173K |
| 代理商： | AK4183 |
ASAHI KASEI
[AK4183]
[Continuous Read mode]
This continuous read operation enables the higher sampling rate and lower processor load than a single read operation. Because
once control command is sent, it does not need to update control command on each read operation until another control command
would like to be rewritten.
MS0500-E-00
2006/04
11
S
A/D data
N
A/D data
N
SDA
D
D
S
A
A
A
M
N
M
D
D
S
P
D
D
D
D
A/D data
N+X
N+X
A/D data
N
M
A
A
A
M
Sr
Repeat
R
Address
Address
R
R
Figure 12 Continuous A/D data Read Sequence
Power on Sequence
It is recommended that the control command must be sent to fix the internal register when power up. This initiates all registers such
as A2-0 bit, PD0 bit, and MODE bit. Once sending command to fix the internal register after first power up, the state of AK4183 is
held on the known-condition of state to ensure that AK4183 is going into desire mode to realize lowest mode. A command with
PD0= “0” should be sent so that AK4183 will be set in the lowest power down mode.
Sleep mode
AK4183 supports the sleep mode that enables touch panel interface to put open state and disables pen interrupt function. AK4183
goes into the sleep mode when control command is sent to AK4183 as shown Table 2. The selection of the sleep mode is set by
“MODE” bit of the control command. The state of both the output of PENIRQN pin and the connection with touch panel interface
(XP, YP, XN, and YN) are the following Table 2. AK4183 keeps the sleep mode until next control command is sent.
Command
MODE bit
0111XX1X
1
0111XX0X
0
PENIRQN
Hi-z
“H” output
Touch panel
Open
Open
Table 2 Sleep Command Setting
The timing of going into the sleep mode is the rising edge of the 16
th
SCL of the write operation. A/D conversion does not execute
when the sleep command is sent. SDA pin is “H” since SDA is pull up.
In order for going to normal mode from sleep mode the command (S= “1”) is sent. The timing of going back to normal mode is the
rising edge of the 16
SCL. When the sleep command is sent again under the sleep mode the mode continues the same as before.
The initial state after power up is in normal mode.
相關PDF資料 |
PDF描述 |
|---|---|
| AK4183VT | I2C Touch Screen Controller |
| AK4184 | TSC with Keypad Scanner and GPIO Expander |
| AK4184VG | TSC with Keypad Scanner and GPIO Expander |
| AK4220 | 7:3 Audio Switch and 6:3 Video Switch |
| AK4220VQ | 7:3 Audio Switch and 6:3 Video Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AK4183_08 | 制造商:AKM 制造商全稱:AKM 功能描述:I2C Touch Screen Controller |
| AK4183KT | 制造商:AKM 制造商全稱:AKM 功能描述:I2C Touch Screen Controller |
| AK4183VT | 制造商:AKM 制造商全稱:AKM 功能描述:I2C Touch Screen Controller |
| AK4184 | 制造商:AKM 制造商全稱:AKM 功能描述:Analog I/F IC which includes 4-wire resistive Touch Screen Controller |
| AK4184A | 制造商:AKM 制造商全稱:AKM 功能描述:TSC with Keypad Scanner and GPIO Expander |
發布緊急采購，3分鐘左右您將得到回復。