- 您現在的位置：買賣IC網 > PDF目錄165355 > ADUM3210ARZ-RL7 (ANALOG DEVICES INC) SPECIALTY ANALOG CIRCUIT, PDSO8 PDF資料下載
參數資料
| 型號： | ADUM3210ARZ-RL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| 封裝： | ROHS COMPLIANT, MS-012AA, SOIC-8 |
| 文件頁數： | 8/20頁 |
| 文件大?。?/td> | 690K |
| 代理商： | ADUM3210ARZ-RL7 |
ADuM3210/ADuM3211
Rev. C | Page 16 of 20
APPLICATIONS INFORMATION
PC BOARD LAYOUT
The ADuM321x digital isolators require no external interface
circuitry for the logic interfaces. Power supply bypassing is
strongly recommended at the input and output supply pins.
The capacitor value should be between 0.01 μF and 0.1 μF.
The total lead length between both ends of the capacitor
and the input power supply pin should not exceed 20 mm.
SYSTEM-LEVEL ESD CONSIDERATIONS AND
ENHANCEMENTS
System-level ESD reliability (for example, per IEC 61000-4-x)
is highly dependent on system design, which varies widely by
application. The ADuM321x incorporate many enhancements
to make ESD reliability less dependent on system design. The
enhancements include:
ESD protection cells were added to all input/output interfaces.
Key metal trace resistances reduced using wider geometry
and paralleling of lines with vias.
The SCR effect inherent in CMOS devices is minimized
by use of a guarding and isolation technique between the
PMOS and NMOS devices.
Areas of high electric field concentration are eliminated
using 45° corners on metal traces.
Supply pin overvoltage is prevented with larger ESD
clamps between each supply pin and its respective ground.
While the ADuM321x improves system-level ESD reliability,
it is no substitute for a robust system-level design. For detailed
recommendations on board layout and system-level design,
see AN-793 Application Note, ESD/Latch-Up Considerations
with iCoupler Isolation Products.
PROPAGATION DELAY-RELATED PARAMETERS
Propagation delay is a parameter that describes the time it takes
a logic signal to propagate through a component. The propagation
delay to a logic low output can differ from the propagation
delay to a logic high output.
INPUT (VIx)
OUTPUT (VOx)
tPLH
tPHL
50%
06
86
6-
00
9
Figure 12. Propagation Delay Parameters
Pulse width distortion is the maximum difference between
these two propagation delay values and is an indication of
how accurately the input signal timing is preserved.
Channel-to-channel matching refers to the maximum amount
that the propagation delay differs between channels within a
single ADuM321x component.
Propagation delay skew refers to the maximum amount that
the propagation delay differs between multiple ADuM321x
components operating under the same conditions.
DC CORRECTNESS AND MAGNETIC FIELD IMMUNITY
Positive and negative logic transitions at the isolator input cause
narrow (~1 ns) pulses to be sent to the decoder via the transformer.
The decoder is bistable and is, therefore, either set or reset by
the pulses, indicating input logic transitions. In the absence of
logic transitions of more than 2 μs at the input, a periodic set of
refresh pulses indicative of the correct input state are sent to
ensure dc correctness at the output. If the decoder receives
no internal pulses for more than approximately 5 μs, the input
side is assumed to be unpowered or nonfunctional, in which
case, the isolator output is forced to a default state (see Table 34
and Table 35) by the watchdog timer circuit.
The ADuM321x is immune to external magnetic fields. The
limitation on the ADuM321x magnetic field immunity is set
by the condition in which induced voltage in the transformer
receiving coil is sufficiently large to either falsely set or reset
the decoder. The following analysis defines the conditions
under which this can occur. The 3 V operating condition of
the ADuM321x is examined because it represents the most
susceptible mode of operation.
The pulses at the transformer output have an amplitude greater
than 1.0 V. The decoder has a sensing threshold at about 0.5 V,
therefore establishing a 0.5 V margin in which induced voltages
can be tolerated. The voltage induced across the receiving coil is
given by
V = (dβ/dt) ∑π rn2, n = 1, 2, ... , N
where:
β is the magnetic flux density (gauss).
N is the number of turns in the receiving coil.
rn is the radius of the nth turn in the receiving coil (cm).
Given the geometry of the receiving coil in the ADuM321x
and an imposed requirement that the induced voltage is at
most 50% of the 0.5 V margin at the decoder, a maximum
allowable magnetic field is calculated as shown in Figure 13.
MAGNETIC FIELD FREQUENCY (Hz)
100
MA
XI
M
U
M
A
L
O
W
A
B
L
E
MA
G
N
ET
IC
F
L
U
X
DE
NS
IT
Y
(
k
g
a
u
ss)
0.001
1M
10
0.01
1k
10k
10M
0.1
1
100M
100k
06
86
6-
0
10
Figure 13. Maximum Allowable External Magnetic Flux Density
相關PDF資料 |
PDF描述 |
|---|---|
| AE101SD1AB | TOGGLE SWITCH, SPDT, LATCHED, 0.02A, 20VDC, THROUGH HOLE-RIGHT ANGLE |
| AE103MD1CB | TOGGLE SWITCH, SPDT, MOMENTARY, 0.02A, 20VDC, THROUGH HOLE-STRAIGHT |
| AE235RAA2N0JSW | 1 ELEMENT, 0.002 uH, CERAMIC-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| AE235RAA2N7JSW | 1 ELEMENT, 0.0027 uH, CERAMIC-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| AE235RAA3N9JSP | 1 ELEMENT, 0.0039 uH, CERAMIC-CORE, GENERAL PURPOSE INDUCTOR, SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUM3210BRZ | 功能描述:IC DIGITAL ISOLATOR 2CH 8-SOIC RoHS:是 類別:隔離器 >> 數字隔離器 系列:iCoupler® 產品培訓模塊:IsoLoop® Isolator 標準包裝:50 系列:IsoLoop® 輸入 - 1 側/2 側:5/0 通道數:5 電源電壓:3 V ~ 5.5 V 電壓 - 隔離:2500Vrms 數據速率:110Mbps 傳輸延遲:12ns 輸出類型:CMOS 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC N 包裝:管件 工作溫度:-40°C ~ 85°C 其它名稱:390-1053-5 |
| ADUM3210BRZ-RL7 | 功能描述:IC DIGITAL ISOLATOR 2CH 8-SOIC RoHS:是 類別:隔離器 >> 數字隔離器 系列:iCoupler® 標準包裝:66 系列:iCoupler® 輸入 - 1 側/2 側:2/2 通道數:4 電源電壓:3.3V，5V 電壓 - 隔離:2500Vrms 數據速率:25Mbps 傳輸延遲:60ns 輸出類型:邏輯 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:管件 工作溫度:-40°C ~ 105°C |
| ADUM3210CRZ | 功能描述:DGTL ISO 2.5KV GEN PURP 8SOIC 制造商:analog devices inc. 系列:* 零件狀態:上次購買時間 標準包裝:98 |
| ADUM3210CRZ-RL7 | 功能描述:DGTL ISO 2.5KV GEN PURP 8SOIC 制造商:analog devices inc. 系列:* 零件狀態:上次購買時間 標準包裝:1 |
| ADUM3210TRZ | 功能描述:IC DIGITAL ISOLATOR 2CH 8-SOIC RoHS:是 類別:隔離器 >> 數字隔離器 系列:iCoupler® 產品培訓模塊:IsoLoop® Isolator 標準包裝:50 系列:IsoLoop® 輸入 - 1 側/2 側:5/0 通道數:5 電源電壓:3 V ~ 5.5 V 電壓 - 隔離:2500Vrms 數據速率:110Mbps 傳輸延遲:12ns 輸出類型:CMOS 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC N 包裝:管件 工作溫度:-40°C ~ 85°C 其它名稱:390-1053-5 |
發布緊急采購，3分鐘左右您將得到回復。