參數資料
型號： ADUC836BCP
廠商： ANALOG DEVICES INC
元件分類： 微控制器/微處理器
英文描述： MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU
中文描述： 8-BIT, FLASH, 12.58 MHz, MICROCONTROLLER, QCC56
封裝： 8 X 8 MM, ROHS COMPLIANT, MO-220-VLLD-2, LFCSP-56
文件頁數： 33/80頁
文件大?。?/td> 5913K
代理商： ADUC836BCP
ADuC836
–33–
Programming the Flash/EE Data Memory
A user wishes to program F3H into the second byte on Page 03H
of the Flash/EE data memory space while preserving the other
three bytes already in this page.
A typical program of the Flash/EE Data array will involve:
1. Setting EADRH/L with the page address
2. Writing the data to be programmed to the EDATA1–4
3. Writing the ECON SFR with the appropriate command
Step 1: Set Up the Page Address
The two address registers, EADRH and EADRL, hold the high
byte address and the low byte address of the page to be addressed.
The assembly language to set up the address may appear as:
MOV
EADRH,#0
;
Set Page Address Pointer
MOV
EADRL,#03H
Step 2: Set Up the EDATA Registers
The four values to be written into the page into the four SFRs
EDATA1–4. Since we do not know three of them,
it is necessary
to read the current page and overwrite the
second byte.
MOV
ECON,#1
;
Read Page into EDATA1-4
MOV
EDATA2,#0F3H
;
Overwrite byte 2
Step 3: Program Page
A byte in the Flash/EE array can be programmed only if it has
previously been erased. To be more specific, a byte can only be
programmed if it already holds the value FFH. Because of the
Flash/EE architecture, this erase must happen at a page level.
Therefore, a minimum of four bytes (1 page) will be erased when
an erase command is initiated. Once the page is erased, we can
program the four bytes in-page and then perform a verification of
the data.
MOV ECON,#5
;
ERASE Page
MOV ECON,#2
;
WRITE Page
MOV ECON,#4
;
VERIFY Page
MOV A,ECON
;
Check if ECON=0 (OK!)
JNZ ERROR
Note that although the four Kbytes of Flash/EE data memory
is shipped from the factory pre-erased, i.e., Byte locations
set to FFH, it is nonetheless good programming practice to
include an erase-all routine as part of any configuration/setup
code running on the ADuC836. An ERASE-ALL command
consists of writing 06H to the ECON SFR, which initiates an
erase of the 4-Kbyte Flash/EE array. This command coded in
8051 assembly would appear as:
MOV ECON,#06H
;
Erase all Command
; 2 ms Duration
Flash/EE Memory Timing
Typical program and erase times for the ADuC836 are as follows:
Normal Mode (operating on Flash/EE data memory)
READPAGE (4 bytes) – 5 machine cycles
WRITEPAGE (4 bytes) – 380
s
VERIFYPAGE (4 bytes) – 5 machine cycles
ERASEPAGE (4 bytes) – 2 ms
ERASEALL (4 Kbytes) – 2 ms
READBYTE (1 byte) – 3 machine cycles
WRITEBYTE (1 byte) – 200
s
ULOAD Mode (operating on Flash/EE program memory)
WRITEPAGE (256 bytes) – 15 ms
ERASEPAGE (64 bytes) – 2 ms
ERASEALL (56 Kbytes) – 2 ms
WRITEBYTE (1 byte) – 200
s
It should be noted that a given mode of operation is initiated as
soon as the command word is written to the ECON SFR. The
core microcontroller operation on the ADuC836 is idled until the
requested Program/Read or Erase mode is completed.
In practice, this means that even though the Flash/EE memory
mode of operation is typically initiated with a two-machine
cycle MOV instruction (to write to the ECON SFR), the next
instruction will not be executed until the Flash/EE operation is
complete. This means that the core will not respond to interrupt
requests until the Flash/EE operation is complete, although the
core peripheral functions like counter/timers will continue to
count and time as configured throughout this period.
REV. A
相關PDF資料
PDF描述
ADUC836BS MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU
ADUC842BCP62-3 MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
ADUC843BCP62-5 MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
ADUC842BCP62-5 MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
ADUC843BCP62-3 MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
相關代理商/技術參數
參數描述
ADUC836BCPZ 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC836BCPZ-REEL 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC836BS 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 52-Pin MQFP 制造商:Analog Devices 功能描述:8BIT MCU +16BIT DUAL ADC MQFP52
ADUC836BS 制造商:Analog Devices 功能描述:IC SEMICONDUCTOR ((NS))
ADUC836BSZ 功能描述:IC ADC DUAL 16BIT W/MCU 52-MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*