參數資料
型號： ADUC831BCP
廠商： ANALOG DEVICES INC
元件分類： 微控制器/微處理器
英文描述： Circular Connector; No. of Contacts:6; Series:LJT07R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:9; Circular Contact Gender:Socket; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:9-35
中文描述： 8-BIT, FLASH, 16.78 MHz, MICROCONTROLLER, QCC56
封裝： 8 X 8 MM, LEAD FRAME, CSP-56
文件頁數： 29/76頁
文件大小： 1211K
代理商： ADUC831BCP
REV. 0
ADuC831
–29–
USING THE FLASH/EE DATA MEMORY
The 4 kBytes of Flash/EE data memory is configured as 1024
pages, each of four bytes. As with the other ADuC831 peripherals,
the interface to this memory space is via a group of registers mapped
in the SFR space. A group of four data registers (EDATA1–4)
are used to hold the four bytes of data at each page. The page is
addressed via the two registers EADRH and EADRL. Finally,
ECON is an 8-bit control register that may be written with one
of nine Flash/EE memory access commands to trigger various
read, write, erase, and verify functions.
A block diagram of the SFR interface to the Flash/EE data
memory array is shown in Figure 20.
ECON—Flash/EE Memory Control SFR
Programming of either the Flash/EE data memory or the Flash/EE
program memory is done through the Flash/EE memory control
SFR (ECON). This SFR allows the user to read, write, erase, or
verify the 4 kBytes of Flash/EE data memory or the 56 kBytes of
Flash/EE program memory.
BYTE 1
(0000H)
E
BYTE 1
(0004H)
BYTE 1
(0008H)
BYTE 1
(000CH)
BYTE 1
(0FF8H)
BYTE 1
(0FFCH)
BYTE 2
(0001H)
E
BYTE 2
(0005H)
BYTE 2
(0009H)
BYTE 2
(000DH)
BYTE 2
(0FF9H)
BYTE 2
(0FFDH)
BYTE 3
(0002H)
E
BYTE 3
(0006H)
BYTE 3
(000AH)
BYTE 3
(000EH)
BYTE 3
(0FFAH)
BYTE 3
(0FFEH)
BYTE 4
(0003H)
E
BYTE 4
(0007H)
BYTE 4
(000BH)
BYTE 4
(000FH)
BYTE 4
(0FFBH)
BYTE 4
(0FFFH)
01H
00H
02H
03H
3FEH
3FFH
P
(
BYTE
ADDRESSES
ARE GIVEN IN
BRACKETS
Figure 20. Flash/EE Data Memory Control and Configuration
Table VII. ECON—Flash/EE Memory Commands
COMMAND DESCRIPTION
(NORMAL MODE) (Power-On Default)
COMMAND DESCRIPTION
(ULOAD MODE)
ECON VALUE
01H
READ
Results in 4 bytes in the Flash/EE data memory,
addressed by the page address EADRH/L, being read
into EDATA1–4.
Not Implemented. Use the MOVC instruction.
02H
WRITE
Results in four bytes in EDATA
1–4
being written to
the
Flash/EE data memory, at the page address given by
EADRH/L (0
≤
EADRH/L < 0400H.
Note: The four bytes in the page being addressed must
be pre-erased.
Results in bytes 0-255 of internal XRAM being written
to the 256 bytes of Flash/EE program memory at the
page address given by EADRH. (0
≤
EADRH < E0H)
Note: The 256 bytes in the page being addressed must
be pre-erased.
03H
Reserved Command
Reserved Command
04H
VERIFY
Verifies if the data in EDATA1–4 is contained in the
page address given by EADRH/L. A subsequent read
of the ECON SFR will result in a 0 being read if the
verification is valid, or a nonzero value being read to
indicate an invalid verification.
Not Implemented. Use the MOVC and MOVX
instructions to verify the WRITE in software.
05H
ERASE PAGE
Results in the Erase of the 4-byte page of Flash/EE data
memory addressed by the page address EADRH/L.
Results in the 64-byte page of Flash/EE program
memory, addressed by the byte address EADRH/L
being erased. EADRL can equal any of 64 locations
within the page. A new page starts whenever EADRL
is equal to 00H, 40H, 80H, or C0H.
06H
ERASE ALL
Results in the erase of entire 4 kBytes of Flash/EE
data memory.
Results in the Erase of the entire 56 kBytes of ULOAD
Flash/EE program memory.
81H
READBYTE
Results in the byte in the Flash/EE data memory,
addressed by the byte address EADRH/L, being read
into EDATA1. (0
≤
EADRH/L
≤
0FFFH).
Not Implemented. Use the MOVC command.
82H
WRITEBYTE
Results in the byte in EDATA1 being written into
Flash/EE data memory, at the byte address EADRH/L.
Results in the byte in EDATA1 being written into
Flash/EE program memory, at the byte address
EADRH/L (0
≤
EADRH/L
≤
DFFFH).
0FH
EXULOAD
Leaves the ECON instructions to operate on the
Flash/EE data memory.
Enters NORMAL mode directing subsequent ECON
instructions to operate on the Flash/EE data memory.
F0H
ULOAD
Enters ULOAD mode, directing subsequent ECON
instructions to operate on the Flash/EE program memory.
Leaves the ECON instructions to operate on the
Flash/EE program memory.
相關PDF資料
PDF描述
ADUC831BS MicroConverter, 12-Bit ADCs and DACs with Embedded 62 kBytes Flash MCU
ADUC836 MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU
ADUC836BCP MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU
ADUC836BS MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU
ADUC842BCP62-3 MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
相關代理商/技術參數
參數描述
ADUC831BCP-REEL 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 56-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:12-BIT ADC WITH EMBEDDED 8-BIT MCU I.C. - Tape and Reel
ADUC831BCPZ 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC831BCPZ-REEL 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC831BS 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 52-Pin MQFP 制造商:Analog Devices 功能描述:8BIT MCU +12BIT ADC LQFP52 831
ADUC831BS-REEL 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 52-Pin MQFP T/R
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*