- 您現在的位置：買賣IC網 > PDF目錄374039 > ADUC7020 (Analog Devices, Inc.) Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU PDF資料下載
參數資料
| 型號： | ADUC7020 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU |
| 中文描述： | 精密模擬微控制器的12位模擬I / O，ARM7TDMI的微控制器 |
| 文件頁數： | 19/80頁 |
| 文件大?。?/td> | 840K |
| 代理商： | ADUC7020 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
Preliminary Technical Data
ADuC702x Series
GENERAL DESCRIPTION
The ADuC702x is fully integrated, 1MSPS, 12-bit data
acquisition system incorporating a high performance multi-
channel ADC, a 16/32-bit MCU and Flash/EE Memory on a
single chip.
Rev. PrB | Page 19 of 80
The ADC consists of up to 12 single-ended inputs. An
additional 4 inputs are available but are multiplexed with the 4
DAC output pins. The 4 DAC outputs are only available on
certain models of the ADuC702x, though in many cases where
the DAC is not present this pin can still be used as an additional
ADC input, giving a maximum of 16 ADC input channels. The
ADC can operate in single-ended or differential input modes.
The ADC input voltage is 0 to V
REF
. Low drift bandgap
reference, temperature sensor and voltage comparator complete
the ADC peripheral set.
The ADuC702x also integrates 4 buffered voltage output DACs
on-chip. The DAC output range is programmable to one of
three voltage ranges.
The device operates from an on-chip oscillator and PLL
generating an internal high-frequency clock of 45 MHz. This
clock is routed through a programmable clock divider from
which the MCU core clock operating frequency is generated.
The microcontroller core is an ARM7TDMI, 16/32-bit RISC
machine, offering up to 45 MIPS peak performance. 62k Bytes
of non-volatile Flash/EE are provided on-chip as well as 8k
Bytes of SRAM. The ARM7TDMI core views all memory and
registers as a single linear array.
On-chip factory firmware supports in-circuit serial download
via the UART and JTAG serial interface ports while non-
intrusive emulation is also supported via the JTAG interface.
These features are incorporated into a low-cost QuickStart
Development System supporting this MicroConverter family.
The parts operate from 2.7V to 3.6V and are specified over an
industrial temperature range of -40°C to 125°C. When
operating at 45MHz the power dissipation is 150mW. The
ADuC702x is available in a variety of memory models and
packages. These are detailed on page 9.
OVERVIEW OF THE ARM7TDMI CORE
The ARM7 core is a 32-bit Reduced Instruction Set Computer
(RISC). It uses a single 32-bit bus for instruction and data. The
length of the data can be 8, 16 or 32 bits and the length of the
instruction word is 32 bits.
The ARM7TDMI is an ARM7 core with 4 additional features:
-
T support for the Thumb (16 bit) instruction set.
-
D support for debug
-
M support for long multiplies
-
I include the EmbeddedICE module to support embedded
system debugging.
Thumb mode (T)
An ARM instruction is 32-bits long. The ARM7TDMI
processor supports a second instruction set that has been
compressed into 16-bits, the Thumb instruction set. Faster
execution from 16-bit memory and greater code density can
usually be achieved by using the Thumb instruction set instead
of the ARM instruction set, which makes the ARM7TDMI core
particularly suitable for embedded applications.
However the Thumb mode has two limitations:
-
Thumb code usually uses more instructions for the same job,
so ARM code is usually best for maximising the performance
of the time-critical code.
-
The Thumb instruction set does not include some
instructions that are needed for exception handling, so the
core will automatically switch to ARM code for exception
handling.
See ARM7TDMI User Guide for details on the core
architecture, the programming model and both the ARM and
ARM Thumb instruction sets.
Long Multiply (M)
The ARM7TDMI instruction set includes four extra
instructions which perform 32-bit by 32-bit multiplication with
64-bit result and 32-bit by 32-bit multiplication-accumulation
(MAC) with 64-bit result. This result is achieved in a reduced
number of cycles than required on a standard ARM7 core.
EmbeddedICE (I)
EmbeddedICE provides integrated on-chip support for the core.
The EmbeddedICE module contains the breakpoint and
watchpoint registers which allow code to be halted for
debugging purposes. These registers are controlled through the
JTAG test port.
When a breakpoint or watchpoint is encountered, the processor
halts and enters debug state. Once in a debug state, the
processor registers may be inspected as well as the Flash/EE, the
SRAM and the Memory Mapped Registers.
Exceptions
ARM supports five types of exceptions, and a privileged
processing mode for each type. The five type of exceptions are:
-
Normal interrupt or IRQ. It is provided to service general-
purpose interrupt handling of internal and external events
-
Fast interrupt or FIQ. It is provided to service data transfer or
communication channel with low latency. FIQ has priority
over IRQ
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC702 | 5 AMP MINIATURE POWER RELAY |
| ADUC814ARU-REEL7 | Circular Connector; MIL SPEC:MIL-DTL-38999 Series I; Body Material:Metal; Series:LJT; No. of Contacts:37; Connector Shell Size:25; Connecting Termination:Crimp; Circular Shell Style:Jam Nut Receptacle; Body Style:Straight RoHS Compliant: No |
| ADUC814BRU | Circular Connector; MIL SPEC:MIL-DTL-38999 Series I; Body Material:Metal; Series:LJT; No. of Contacts:37; Connector Shell Size:25; Connecting Termination:Crimp; Circular Shell Style:Jam Nut Receptacle; Body Style:Straight RoHS Compliant: No |
| ADUC814BRU-REEL | Circular Connector; No. of Contacts:56; Series:LJT07R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:25; Circular Contact Gender:Pin; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:25-4 |
| ADUC814BRU-REEL7 | Circular Connector; No. of Contacts:61; Series:LJT07R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:25; Circular Contact Gender:Pin; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:25-61 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC7020BCP62 | 制造商:Analog Devices 功能描述:FLASH ARM7+5-CH,12-B ADC & 4X12-B DAC IC - Trays |
| ADUC7020BCP62-U1 | 制造商:Analog Devices 功能描述:FLASH ARM7+5-CH,12-B ADC & 4X12-B DAC IC - Trays |
| ADUC7020BCPZ62 | 功能描述:IC MCU FLSH 62K ANLG I/O 40LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:60 系列:PSOC® 3 CY8C38xx 核心處理器:8051 芯體尺寸:8-位 速度:67MHz 連通性:EBI/EMI，I²C，LIN，SPI，UART/USART 外圍設備:電容感應，DMA，LCD，POR，PWM，WDT 輸入/輸出數:25 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:2K x 8 RAM 容量:8K x 8 電壓 - 電源 (Vcc/Vdd):1.71 V ~ 5.5 V 數據轉換器:A/D 2x20b，D/A 4x8b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-VFQFN 裸露焊盤 包裝:托盤 |
| ADUC7020BCPZ62I | 功能描述:IC MCU FLSH 62K ANLG I/O 40LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:60 系列:PSOC® 3 CY8C38xx 核心處理器:8051 芯體尺寸:8-位 速度:67MHz 連通性:EBI/EMI，I²C，LIN，SPI，UART/USART 外圍設備:電容感應，DMA，LCD，POR，PWM，WDT 輸入/輸出數:25 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:2K x 8 RAM 容量:8K x 8 電壓 - 電源 (Vcc/Vdd):1.71 V ~ 5.5 V 數據轉換器:A/D 2x20b，D/A 4x8b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-VFQFN 裸露焊盤 包裝:托盤 |
| ADUC7020BCPZ62I-RL | 功能描述:IC MCU 12BIT 1MSPS I2C 40-LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
發布緊急采購，3分鐘左右您將得到回復。