- 您現在的位置：買賣IC網 > PDF目錄165354 > ADS8412IPFBTG4 (TEXAS INSTRUMENTS INC) 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PQFP48 PDF資料下載
參數資料
| 型號： | ADS8412IPFBTG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | ADC |
| 英文描述： | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PQFP48 |
| 封裝： | GREEN, PLASTIC, TQFP-48 |
| 文件頁數： | 16/29頁 |
| 文件大?。?/td> | 1018K |
| 代理商： | ADS8412IPFBTG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
www.ti.com
LAYOUT
ADS8412
SLAS384A – JUNE 2003 – REVISED DECEMBER 2004
For optimum performance, care should be taken with the physical layout of the ADS8412 circuitry.
As the ADS8412 offers single-supply operation, it is often used in close proximity with digital logic,
microcontrollers, microprocessors, and digital signal processors. The more digital logic present in the design and
the higher the switching speed, the more difficult it is to achieve good performance from the converter.
The basic SAR architecture is sensitive to glitches or sudden changes on the power supply, reference, ground
connections and digital inputs that occur just prior to latching the output of the analog comparator. Thus, driving
any single conversion for an n-bit SAR converter, there are at least n windows in which large external transient
voltages can affect the conversion result. Such glitches might originate from switching power supplies, nearby
digital logic, or high power devices.
The degree of error in the digital output depends on the reference voltage, layout, and the exact timing of the
external event.
On average, the ADS8412 draws very little current from an external reference, as the reference voltage is
internally buffered. If the reference voltage is external and originates from an op amp, make sure that it can drive
the bypass capacitor or capacitors without oscillation. A 0.1-F bypass capacitor and 1-F storage capacitor are
recommended from pin 1 (REFIN) directly to pin 48 (REFM). REFM and AGND should be shorted on the same
ground plane under the device.
The AGND and BDGND pins should be connected to a clean ground point. In all cases, this should be the
analog ground. Avoid connections which are close to the grounding point of a microcontroller or digital signal
processor. If required, run a ground trace directly from the converter to the power supply entry point. The ideal
layout consists of an analog ground plane dedicated to the converter and associated analog circuitry.
As with the AGND connections, +VA should be connected to a 5-V power supply plane or trace that is separate
from the connection for digital logic until they are connected at the power entry point. Power to the ADS8412
should be clean and well bypassed. A 0.1-F ceramic bypass capacitor should be placed as close to the device
as possible. See Table 3 for the placement of the capacitor. In addition, a 1-F to 10-F capacitor is
recommended. In some situations, additional bypassing may be required, such as a 100-F electrolytic capacitor
or even a Pi filter made up of inductors and capacitors—all designed to essentially low-pass filter the 5-V supply,
removing the high frequency noise.
Table 3. Power Supply Decoupling Capacitor Placement
POWER SUPPLY PLANE
CONVERTER ANALOG SIDE
CONVERTER DIGITAL SIDE
SUPPLY PINS
(4,5), (8,9), (10,11), (13,15), (43,44),
Pin pairs that require shortest path to decoupling capacitors
(24,25), (34, 35)
(45,46)
Pins that require no decoupling
12, 14
37
23
相關PDF資料 |
PDF描述 |
|---|---|
| ADS8412IBPFBTG4 | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PQFP48 |
| ADS8412IPFBRG4 | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PQFP48 |
| ADS8517IDWR | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, PDSO28 |
| ADS8517IDW | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, PDSO28 |
| ADS8517IPWR | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADS8413 | 制造商:BB 制造商全稱:BB 功能描述:16-BIT, 1-MSPS, PSEUDO-BIPOLAR, FULLY DIFFERENTIAL INPUT, MICROPOWER SAMPLING ANALOG-TO-DIGITAL CONVERTER WITH PARALLEL INTERFACE, REFERENCE |
| ADS8413IBRGZR | 功能描述:模數轉換器 - ADC 16-bit Uni Diff In Smp rt 4.75-5.25V RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS8413IBRGZRG4 | 功能描述:模數轉換器 - ADC 16-bit Uni Diff In Smp rt 4.75-5.25V RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS8413IBRGZT | 功能描述:模數轉換器 - ADC 16-bit Uni Diff In Smp rt 4.75-5.25V RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS8413IBRGZTG4 | 功能描述:模數轉換器 - ADC 16-bit Uni Diff In Smp rt 4.75-5.25V RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。