- 您現在的位置：買賣IC網 > PDF目錄366333 > ADNS-5020-EN (Avago Technologies Ltd.) Optical Mouse Sensor PDF資料下載
參數資料
| 型號： | ADNS-5020-EN |
| 廠商： | Avago Technologies Ltd. |
| 英文描述： | Optical Mouse Sensor |
| 中文描述： | 光學鼠標傳感器 |
| 文件頁數： | 11/24頁 |
| 文件大小： | 278K |
| 代理商： | ADNS-5020-EN |
11
LED Mode
For power savings, the LED will not be continuously on.
ADNS-5020-EN will pulse the LED only when needed.
Synchronous Serial Port
The synchronous serial port is used to set and read
parameters in the ADNS-5020-EN, and to read out the
motion information.
The port is a three wire serial port. The host micro-con-
troller always initiates communication; the ADNS-5020-EN
never initiates data transfers. SCLK, SDIO, and NCS may be
driven directly by a micro-controller. The port pins may be
shared with other SPI slave devices. When the NCS pin is
high, the inputs are ignored and the output is tri-stated.
The lines that comprise the SPI port:
SCLK:
Clock input. It is always generated by the master
(the micro-controller).
Input and Output data.
Chip select input (active low). NCS needs to be
low to activate the serial port; otherwise, SDIO
will be high Z, and SDIO & SCLK will be ignored.
NCS can also be used to reset the serial port in
case of an error.
SDIO:
NCS:
Write Operation
SDIO Setup and Hold Time
Chip Select Operation
The serial port is activated after NCS goes low. If NCS
is raised during a transaction, the entire transaction
is aborted and the serial port will be reset. This is true
for all transactions. After a transaction is aborted, the
normal address-to-data or transaction-to-transaction
delay is still required before beginning the next trans-
action. To improve communication reliability, all serial
transactions should be framed by NCS. In other words,
the port should not remain enabled during periods of
non-use because ESD and EFT/B events could be inter-
preted as serial communication and put the chip into an
unknown state. In addition, NCS must be raised after
each burst-mode transaction is complete to terminate
burst-mode. The port is not available for further use until
burst-mode is terminated.
Write Operation
Write operation, defined as data going from the micro-
controller to the ADNS-5020-EN, is always initiated by
the micro-controller and consists of two bytes. The first
byte contains the address (seven bits) and has a “1” as its
MSB to indicate data direction. The second byte contains
the data. The ADNS-5020-EN reads SDIO on rising edges
of SCLK.
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
2
1
D0
D5
D6
D7
A0
A1
A2
A3
A4
A5
A6
1
A6
D4
D3
D2
D1
SCLK
NCS
SDIO
SDIO DRIVEN BY MICRO-CONTROLLER
t
setup
1/
f
SCLK
1/
f
SCLK
t
hold
SCLK
SDIO
相關PDF資料 |
PDF描述 |
|---|---|
| ADNS-5030 | Low Power Optical Mouse Sensor |
| ADNS-5100 | Solid-State Optical Mouse Lens |
| ADNS-5100-001 | Solid-State Optical Mouse Lens |
| ADPDC2BB4AW | General Purpose Snap-acting Switches |
| ADGGF3B14AC | General Purpose Snap-acting Switches |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADNS-5030 | 功能描述:光學導航傳感器 Optical Mouse Sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-5050 | 功能描述:光學導航傳感器 Navigation Sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-5060 | 功能描述:光學導航傳感器 Navigation Sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-5070 | 功能描述:光學導航傳感器 USB/PS2 LED Sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-5090 | 功能描述:光學導航傳感器 Wireless Optical Sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
發布緊急采購，3分鐘左右您將得到回復。