參數資料
型號: ADN2818ACPZ
廠商: Analog Devices Inc
文件頁數: 11/40頁
文件大小: 0K
描述: IC CLOCK/DATA RECOVERY 32-LFCSP
標準包裝: 1
類型: 時鐘和數據恢復(CDR),多路復用器
PLL:
主要目的: SONET/SDH
輸入: CML
輸出: CML
電路數: 1
比率 - 輸入:輸出: 1:2
差分 - 輸入:輸出: 是/是
頻率 - 最大: 2.7GHz
電源電壓: 3 V ~ 3.6 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 32-VFQFN 裸露焊盤,CSP
供應商設備封裝: 32-LFCSP-VQ(5x5)
包裝: 托盤
產品目錄頁面: 788 (CN2011-ZH PDF)
Data Sheet
ADN2817/ADN2818
Rev. E | Page 19 of 40
JITTER SPECIFICATIONS
The ADN2817/ADN2818 CDR is designed to achieve the best
bit error rate (BER) performance and exceeds the jitter transfer,
generation, and tolerance specifications proposed for SONET/SDH
equipment defined in the Telcordia Technologies specification.
Jitter is the dynamic displacement of digital signal edges from
their long-term average positions, measured in unit intervals
(UI), where 1 UI = 1 bit period. Jitter on the input data can cause
dynamic phase errors on the recovered clock sampling edge. Jitter
on the recovered clock causes jitter on the retimed data.
The following sections briefly summarize the specifications
of jitter generation, transfer, and tolerance in accordance with
the Telcordia document (GR-253-CORE, Issue 3, September
2000) for the optical interface at the equipment level and the
ADN2817/ADN2818 performance with respect to those
specifications.
JITTER GENERATION
The jitter generation specification limits the amount of jitter
that can be generated by the device with no jitter and wander
applied at the input. For OC-48 devices, the band-pass filter
has a 12 kHz high-pass cutoff frequency with a roll-off of
20 dB/decade and a low-pass cutoff frequency of at least
20 MHz. The jitter generated must be less than 0.01 UI rms
and must be less than 0.1 UI p-p.
JITTER TRANSFER
The jitter transfer function is the ratio of the jitter on the output
signal to the jitter applied on the input signal vs. the frequency.
This parameter measures the limited amount of the jitter on
an input signal that can be transferred to the output signal
0.1
ACCEPTABLE
RANGE
fC
JITTER FREQUENCY (kHz)
SLOPE = –20dB/DECADE
JI
TTE
R
GA
IN
(
d
B
)
0
60
01-
01
5
Figure 26. Jitter Transfer Curve
JITTER TOLERANCE
The jitter tolerance is defined as the peak-to-peak amplitude of
the sinusoidal jitter applied on the input signal, which causes a
1 dB power penalty. This is a stress test intended to ensure that
no additional penalty is incurred under the operating conditions
15.00
1.50
0.15
f0
f1
f2
f3
f4
JITTER FREQUENCY (kHz)
SLOPE = –20dB/DECADE
IN
P
U
T
J
ITT
E
R
A
M
P
L
ITU
D
E
(
U
I
p-
p
)
060
01
-01
6
Figure 27. SONET Jitter Tolerance Mask
相關PDF資料
PDF描述
XRT91L31IQ-F IC TXRX SONET/SDH 8BIT 64QFP
MS27496E19A32S CONN RCPT 32POS BOX MNT W/SCKT
AD9548BCPZ IC CLOCK GEN/SYNCHRONIZR 88LFCSP
V375C36M150BL3 CONVERTER MOD DC/DC 36V 150W
MAX3676EHJ+ IC CLOCK RECOVERY 32-TQFP
相關代理商/技術參數
參數描述
ADN2818ACPZ-RL 制造商:AD 制造商全稱:Analog Devices 功能描述:Continuous Rate 10 Mbps to 2.7 Gbps Clock and Data Recovery ICs
ADN2818ACPZ-RL7 功能描述:IC CLOCK/DATA RECOVERY 32-LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP (0.240",6.10mm 寬) 供應商設備封裝:64-TSSOP 包裝:管件
ADN2819 制造商:AD 制造商全稱:Analog Devices 功能描述:Multirate to 2.7 Gb/s Clock and Data Recovery IC with Integrated Limiting Amp
ADN2819ACP-CML 制造商:Analog Devices 功能描述:CDR 2488.32Mbps/2666.06Mbps SONET/SDH 48-Pin LFCSP EP Tray 制造商:Rochester Electronics LLC 功能描述:MULTI-RATE 2.7GBPS CDR/ PA LOW POWER I.C - Bulk
ADN2819ACP-CML-RL 制造商:Analog Devices 功能描述:CDR 2488.32Mbps/2666.06Mbps SONET/SDH 48-Pin LFCSP EP T/R