
ADG3242
Rev. A | Page 3 of 16
SPECIFICATIONS
VCC = 2.3 V to 3.6 V, GND = 0 V; all specifications TMIN to TMAX, unless otherwise noted.
Table 1.
Parameter
Symbol
Conditions
Min
Max
Unit
DC ELECTRICAL CHARACTERISTICS
Input High Voltage
VINH
VCC = 2.7 V to 3.6 V
2.0
V
VCC = 2.3 V to 2.7 V
1.7
V
Input Low Voltage
VINL
VCC = 2.7 V to 3.6 V
0.8
V
VCC = 2.3 V to 2.7 V
0.7
V
Input Leakage Current
II
±0.01
±1
μA
Off State Leakage Current
IOZ
0 ≤ A, B ≤ VCC
±0.01
±1
μA
On State Leakage Current
0 ≤ A, B ≤ VCC
±0.01
±1
μA
Maximum Pass Voltage
VP
VA/VB = VCC = SEL = 3.3 V, IO = 5 μA
2.0
2.5
2.9
V
VA/VB = VCC = SEL = 2.5 V, IO = 5 μA
1.5
1.8
2.1
V
VA/VB = VCC = 3.3 V, SEL = 0 V, IO = 5 μA
1.5
1.8
2.1
V
A Port Off Capacitance
CA OFF
f = 1 MHz
3.5
pF
B Port Off Capacitance
CB OFF
f = 1 MHz
3.5
pF
A, B Port On Capacitance
CA, CB ON
f = 1 MHz
7
pF
Control Input Capacitance
CIN
f = 1 MHz
4
pF
SWITCHING CHARACTERIST
ICS3Propagation Delay A to B or B to A, t
PD4tPHL, tPLH
CL = 50 pF, VCC = SEL = 3 V
0.225
ns
5
ps
Bus Enable Time BE to A or B
6tPZH, tPZL
VCC = 3.0 V to 3.6 V; SEL = VCC
1
3.2
4.6
ns
VCC = 3.0 V to 3.6 V; SEL = 0 V
1
3
4
ns
VCC = 2.3 V to 2.7 V; SEL = VCC
1
3
4
ns
Bus Disable Time BE to A or
B6tPHZ, tPLZ
VCC = 3.0 V to 3.6 V; SEL = VCC
1
3
4
ns
VCC = 3.0 V to 3.6 V; SEL = 0 V
1
2.5
3.8
ns
VCC = 2.3 V to 2.7 V; SEL = VCC
1
2.5
3.4
ns
Maximum Data Rate
VCC = SEL = 3.3 V; VA/VB = 2 V
1.5
Gbps
Channel Jitter
VCC = SEL = 3.3 V; VA/VB = 2 V
45
ps p-p
DIGITAL SWITCH
On Resistance
RON
VCC = 3 V, SEL = VCC, VA = 0 V, IBA = 8 mA
4.5
8
Ω
VCC = 3 V, SEL = VCC, VA = 1.7 V, IBA = 8 mA
12
28
Ω
VCC = 2.3 V, SEL = VCC, VA = 0 V, IBA = 8 mA
5
9
Ω
VCC = 2.3 V, SEL = VCC, VA = 1 V, IBA = 8 mA
9
18
Ω
VCC = 3 V, SEL = 0 V, VA = 0 V, IBA = 8 mA
5
8
Ω
VCC = 3 V, SEL = 0 V, VA = 1 V, IBA = 8 mA
12
Ω
On Resistance Matching
RON
VCC = 3 V, SEL = VCC, VA = 0 V, IA = 8 mA
0.1
0.5
Ω
VCC = 3 V, SEL = 0 V, VA = 0 V, IA = 8 mA
0.1
0.5
Ω
POWER REQUIREMENTS
VCC
2.3
3.6
V
Quiescent Power Supply Current
ICC
Digital inputs = 0 V or VCC; SEL = VCC
0.01
1
μA
Digital inputs = 0 V or VCC ; SEL = 0 V
0.1
0.2
mA
ICC
VCC = 3.6 V, BE = 3.0 V; SEL = VCC
0.15
8
μA
1 Temperature range is as follows: B version: 40°C to +85°C.
2 Typical values are at 25°C, unless otherwise stated.
3 Guaranteed by design, not subject to production test.
4 The digital switch contributes no propagation delay other than the RC delay of the typical RON of the switch and the load capacitance when driven by an ideal voltage
source. Because the time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagation delay to the system. Propagation
delay of the digital switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side.
5 Propagation delay matching between channels is calculated from the on resistance matching and load capacitance of 50 pF.
7 This current applies to the Control Pin BE only. The A and B ports contribute no significant ac or dc currents as they transition.