參數資料
型號: ADE7169ACPF16-RL
廠商: ANALOG DEVICES INC
元件分類: 模擬信號調理
英文描述: Single-Phase Energy Measurement IC with 8052 MCU, RTC and LCD driver
中文描述: ANALOG CIRCUIT, QCC64
封裝: 9 X 9MM, MO-220VMMD, LFCSP-64
文件頁數: 123/140頁
文件大小: 1359K
代理商: ADE7169ACPF16-RL
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁當前第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁
Preliminary Technical Data
ADE7169F16
SERIAL PERIPHERAL INTERFACE
INTERFACE (SPI)
The ADE7169F16 integrates a complete hardware serial
peripheral interface on-chip. The SPI interface is full duplex so
that eight bits of data are synchronously transmitted and
received simultaneously. This SPI implementation is double
buffered. This allows the user to read the last byte of received
data while a new byte is shifted in. The next byte to be
transmitted can be loaded while the current byte is shifted out.
Rev. PrD | Page 123 of 140
The SPI port can be configured for Master or Slave operation.
The physical interface to the SPI is done via MISO (P0.3),
MOSI (P0.2), SCLK (P0.4) and
SS
(P0.5) pins, while the
firmware interface is done via the
SPI Configuration Register SFR
(SPIMOD1, 0xE8)
,
SPI Configuration Register SFR (SPIMOD2,
0xE9)
,
SPI Interrupt Status Register SFR (SPISTAT, 0xEA)
,
SPI/I2C
Transmit Buffer SFR (SPI2CTx, 0x9A)
and
SPI Receive Buffer SFR
(SPI2CRx, 0x9B)
.
Note that the SPI pins are shared with the I
2
C pins. Therefore,
the user can enable only one interface at a time. The SCPS bit in
the CFG SFR selects which peripheral is active.
SPI SFR REGISTER LIST
SFR Address
Name
R/W
Length
Default
Value
0
0x10
0
0
Description
0x9A
0x9B
0xE8
0xE9
0xEA
SPI2CTx
SPI2CRx
SPIMOD1
SPIMOD2
SPI2CSTAT
W
R
R/W
R/W
R/W
8
8
8
8
8
SPI Data out register
SPI Data in register
SPI configuration register
SPI configuration register
SPI/I2C Interrupt Status register
Table 121: SPI SFR register list
Table 122. SPI/I2C Transmit Buffer SFR (SPI2CTx, 0x9A)
Bit
Location
Mnemonic
7-0
SPI2CTx
Bit
Default
Value
Description
0
SPI or I2C transmit buffer
When SPI2CTx SFR is written, its content is transfered to the transmit FIFO input.
When a write is requested, the FIFO output is sent on the SPI or I2C bus.
Table 123. SPI Receive Buffer SFR (SPI2CRx, 0x9B)
Bit
Location
Mnemonic
7-0
SPI2CRx
Bit
Default
Value
Description
0
SPI or I2C receive buffer
When SPI2CRx SFR is read, one byte from the Receive FIFO output is transfered to
SPI2CRx SFR. A new data from the SPI or I2C bus is written to the FIFO input.
Table 124. SPI Configuration Register SFR (SPIMOD1, 0xE8)
Bit
Location
Addr.
Name
7-5
0xEF –
0xEE
5
0xED
INTMOD
Bit
Bit
Default
Value
Description
Reserved
0
Reserved
0
SPI Interrupt mode
0: SPI Interrupt set when SPI Rx buffer full
1: SPI interrupt set when SPI Tx buffer empty
Master Mode: SS output control. See Figure 82.
0
The SS is held low while this bit is clear. This allows manual chip select
control using the SS pin.
Single Byte Read or Write: The SS will go low during a single byte
transmission and then return high.
Continuous Transfer: The SS will go low during the duration of the multi-
byte continuous transfer and then return high.
Slave Mode: SS input enable
0xEC
4
AUTO_SS
1
1
3
0xEB
SSE
0
相關PDF資料
PDF描述
ADE7169ACPZF16 Single-Phase Energy Measurement IC with 8052 MCU, RTC and LCD driver
ADE7169ACPZF16-RL Single-Phase Energy Measurement IC with 8052 MCU, RTC and LCD driver
ADE7169ASTF16 Single-Phase Energy Measurement IC with 8052 MCU, RTC and LCD driver
ADE7169ASTF16-RL Single-Phase Energy Measurement IC with 8052 MCU, RTC and LCD driver
ADE7169ASTZF16 Single-Phase Energy Measurement IC with 8052 MCU, RTC and LCD driver
相關代理商/技術參數
參數描述
ADE7169ACPZF16 制造商:AD 制造商全稱:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver
ADE7169ACPZF161 制造商:AD 制造商全稱:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC and LCD driver
ADE7169ACPZF16-RL 制造商:AD 制造商全稱:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver
ADE7169ACPZF16-RL1 制造商:AD 制造商全稱:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC and LCD driver
ADE7169ASTF16 制造商:AD 制造商全稱:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC and LCD driver