參數資料
型號: ADC1410S065HN
廠商: NXP Semiconductors N.V.
元件分類: 外設及接口
英文描述: Single 14-bit ADC 65 Msps CMOS or LVDS DDR digital outputs
封裝: ADC1410S065HN/C1<SOT618-1 (HVQFN40)|<<http://www.nxp.com/packages/SOT618-1.html<1<Always Pb-free,;ADC1410S065HN/C1<SOT618-1 (HVQFN40)|<<http://www.nxp.com/packages/SOT618
文件頁數: 28/40頁
文件大?。?/td> 551K
代理商: ADC1410S065HN
ADC1410S_SER
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 4 — 24 December 2010
28 of 40
NXP Semiconductors
ADC1410S series
Single 14-bit ADC; CMOS or LVDS DDR digital output
Table 18.
W1
0
0
1
1
Bits A12 to A0 indicate the address of the register being accessed. In the case of a
multiple byte transfer, this address is the first register to be accessed. An address counter
is increased to access subsequent addresses.
The steps involved in a data transfer are as follows:
1. A falling edge on CS in combination with a rising edge on SCLK determine the start of
communications.
2. The first phase is the transfer of the 2-byte instruction.
3. The second phase is the transfer of the data which can vary in length but is always a
multiple of 8 bits. The MSB is always sent first (for instruction and data bytes).
4. A rising edge on CS indicates the end of data transmission.
11.6.2
Default modes at start-up
During circuit initialization it does not matter which output data standard has been
selected. At power-up, the device enters Pin control mode.
A falling edge on CS triggers a transition to SPI control mode. When the ADC1410S
enters SPI control mode, the output data standard (CMOS/LVDS DDR) is determined by
the level on pin SDIO (see
Figure 37
). Once in SPI control mode, the output data standard
can be changed via bit LVDS_CMOS
in
Table 23
.
When the ADC1410S enters SPI control mode, the output data format (two’s complement
or offset binary) is determined by the level on pin SCLK (gray code can only be selected
via the SPI). Once in SPI control mode, the output data format can be changed via bit
DATA_FORMAT[1:0] in
Table 23
.
Number of data bytes to be transferred after the instruction bytes
W0
Number of bytes transmitted
0
1 byte
1
2 bytes
0
3 bytes
1
4 bytes or more
Fig 36. SPI mode timing
SCLK
SDIO
R/W
W1
W0
A12 A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
D7
D6
D5
D4
D3
D2
D1
D3
D2
D1
D0
D0
D7
D6
D5
D4
Instruction bytes
Register N (data)
Register N + 1 (data)
005aaa062
CS
相關PDF資料
PDF描述
ADC1410S065HN Single 14-bit ADC 65 Msps CMOS or LVDS DDR digital outputs
ADC1410S080HN Single 14-bit ADC 80 Msps CMOS or LVDS DDR digital outputs
ADC1410S105HN Single 14-bit ADC 105 Msps CMOS or LVDS DDR digital outputs
ADC1410S125HN Single 14-bit ADC 125 Msps CMOS or LVDS DDR digital outputs
ADC1412D065HN Dual 14-bit ADC 65 Msps CMOS or LVDS DDR digital outputs
相關代理商/技術參數
參數描述
ADC1410S065HN,518 功能描述:模數轉換器 - ADC SNGLE 14b ADC 65MSPS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
ADC1410S065HN/C1,5 功能描述:模數轉換器 - ADC SGL 14b ADC 65 MSPS CMOS OR LVDS DDR RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
ADC1410S065HN-C1 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
ADC1410S065HN-C18 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32