參數資料
型號: ADAU1701JSTZ-RL
廠商: ANALOG DEVICES INC
元件分類: 消費家電
英文描述: SigmaDSP 28/56-Bit Audio Processor with 2ADC/4DAC
中文描述: SPECIALTY CONSUMER CIRCUIT, PQFP48
封裝: ROHS COMPLIANT, PLASTIC, MS-026BBC, LQFP-48
文件頁數: 28/43頁
文件大?。?/td> 625K
代理商: ADAU1701JSTZ-RL
ADAU1701
Preliminary Technical Data
DSP CORE CONTROL REGISTER
The controls in this register set the operation of the
ADAU1701’s DSP core.
Table 26. DSP Core Control Register (2076)
Register Bits
Function
15:14
Reserved
13:12
GPIO Debounce control
00 = 20ms
01 = 40ms
10 = 10ms
11 = 5ms
11:9
Reserved
8
Aux ADC Data registers control port write mode
7
GPIO Pin Setting register control port write
mode
6
Interface registers control port write mode
5
Initiate Safeload Transfer
4
Mute ADCs, active low
3
Mute DACs, active low
2
Clear Internal Registers to All Zeros, active low
1:0
Sample Rate
00 = 1× (1024 instructions, 48 kHz)
01 = 2× (512 instructions, 96 kHz)
10 = 4× (256 instructions, 192 kHz)
00 = reserved
GPIO Debounce control (Bits 13:12)
Set debounce time of multipurpose pins set as GPIO inputs.
Rev. PrF | Page 28 of 43
Aux ADC Data registers control port write mode (Bit 8)
Setting this bit allows data to be written directly to the Aux
ADC Data registers (2057-2060) from the control port. When
set, the Aux ADC Data registers will no longer respond to
settings on the multi-purpose pins.
GPIO Pin Setting register control port write mode (Bit 7)
When this bit is set, the GPIO Pin Setting register (2056) can be
written to directly from the control port and this register will no
longer respond to input settings on the multi-purpose pins.
Interface registers control port write mode (Bit 6)
When this bit is set, data can be written directly to the Interface
registers (2048-2055) from the control port. In that state, the
Interface registers will not be written from the SigmaDSP
program.
Initiate Safe Transfer to Parameter RAM (Bit 5)
Setting this bit to 1 initiates a safeload transfer to the parameter
RAM. This bit is automatically cleared when the operation is
completed. There are five safeload register pairs (address/data);
only those registers that have been written since the last
safeload event are transferred to the parameter RAM.
Mute ADCs (Bit 4)
This bit will mute the output of the ADCs. The bit defaults to 0
and is active-low, so it must be set to 1 in order to pass audio
from the ADCs.
Mute DACs (Bit 3)
This bit will mute the output of the DACs. The bit defaults to 0
and is active-low, so it must be set to 1 in order to pass audio
from the DACs.
Clear Internal Registers to All Zeros (Bit 2)
This bit defaults to 0 and is active low. This bit needs to be set to
1 in order for a signal to pass through the SigmaDSP core.
Sample Rate (Bits 1:0)
These bits set the number of DSP instructions for every sample
and the sample rate at which the ADAU1701 will operate. At the
default setting of 1× there will be 1024 instructions per audio
sample. This setting should be used with sample rates such as
48 kHz and 44.1 kHz.
In the 2× setting the number of instructions per frame will be
halved to 512 and the ADCs and DACs will nominally run at a
96 kHz sample rate.
At a 4× setting there will be 256 instructions per cycle and the
converters will run at a 192 kHz sample rate.
INTERFACE REGISTERS
The interface registers are used in self-boot mode to save
parameters that need to be written to the external EEPROM.
The ADAU1701 will then recall these parameters from the
EEPROM after the next reset or power-up. This way, system
parameters such as volume and EQ settings can be saved during
power-down and recalled when the system is next turned on.
There are eight 32-bit interface registers, which allows for eight
28-bit (plus zero-padding) parameters to be saved. The
parameters that will be saved in these registers are set in the
graphical programming tools. These registers are updated with
their corresponding parameter RAM data once per sample
period.
An edge, which can be set to be either rising or falling, triggers
the ADAU1701 to write the current contents of the interface
registers to the EEPROM. See more information in the Self boot
section.
The user can write directly to the interface registers after bit 6 in
the DSP core control register has been set. In this mode, the
data in the registers is written from the control port and not
from the DSP core.
CONTROL PORT READ/WRITE DATA FORMATS
The read/write formats of the control port are designed to be
byte-oriented. This allows for easy programming of common
相關PDF資料
PDF描述
ADAV400 Audio Codec with Embedded SigmaDSP Processor
ADAV400KSTZ Audio Codec with Embedded SigmaDSP Processor
ADAV400KSTZ-REEL Audio Codec with Embedded SigmaDSP Processor
ADAV803 Audio Codec for Recordable DVD
ADAV803ASTZ 8-Channel 14-Bit Single-Supply Voltage-Output DAC; Package: LQFP (10x10mm); No of Pins: 52; Temperature Range: Industrial
相關代理商/技術參數
參數描述
ADAU1701MINIBZ 制造商:Analog Devices 功能描述:EVAL BD SIGMADSPMULTICHANAUDIO PROCESSOR - Bulk
ADAU1702 制造商:AD 制造商全稱:Analog Devices 功能描述:SigmaDSP 28-56-Bit Audio Processor with Two ADCs and Four DACs
ADAU1702JSTZ 功能描述:IC AUDIO PROC 2ADC/4DAC 48-LQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻處理 系列:SigmaDSP® 其它有關文件:STA321 View All Specifications 標準包裝:1 系列:Sound Terminal™ 類型:音頻處理器 應用:數字音頻 安裝類型:表面貼裝 封裝/外殼:64-LQFP 裸露焊盤 供應商設備封裝:64-LQFP EP(10x10) 包裝:Digi-Reel® 其它名稱:497-11050-6
ADAU1702JSTZ-RL 功能描述:IC AUDIO PROC 2ADC/4DAC 48-LQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻處理 系列:SigmaDSP® 其它有關文件:STA321 View All Specifications 標準包裝:1 系列:Sound Terminal™ 類型:音頻處理器 應用:數字音頻 安裝類型:表面貼裝 封裝/外殼:64-LQFP 裸露焊盤 供應商設備封裝:64-LQFP EP(10x10) 包裝:Digi-Reel® 其它名稱:497-11050-6
ADAU1761 制造商:AD 制造商全稱:Analog Devices 功能描述:SigmaDSP Stereo, Low Power, 96 kHz, 24-Bit Audio Codec with Integrated PLL