- 您現在的位置：買賣IC網 > PDF目錄2063 > ADAU1592ACPZ (Analog Devices Inc)IC AMP AUDIO PWR 24W 48LFCSP PDF資料下載
參數資料
| 型號： | ADAU1592ACPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 9/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP AUDIO PWR 24W 48LFCSP |
| 標準包裝： | 1 |
| 類型： | D 類 |
| 輸出類型： | 2 通道（立體聲） |
| 在某負載時最大輸出功率 x 通道數量： | 24W x 2 @ 4 歐姆 |
| 電源電壓： | 9 V ~ 18 V |
| 特點： | 消除爆音，靜音，短路和熱保護，待機 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 48-LFCSP-VQ（7x7） |
| 封裝/外殼： | 48-VFQFN 裸露焊盤，CSP |
| 包裝： | 托盤 |
| 產品目錄頁面： | 776 (CN2011-ZH PDF) |
ADAU1592
Rev. A | Page 17 of 24
on the outputs after the LC filter. Typical short-circuit condi-
tions include shorting of the output load and shorting to either
PVDD or PGND.
UNDERVOLTAGE PROTECTION
The ADAU1592 is also comprised of an undervoltage protec-
tion circuit, which senses the undervoltage on PVDD. When
the PVDD supply goes below the operating threshold, the
output FETs are turned to a high-Z condition. In addition, the
device issues an error flag by pulling ERR low. This condition
is latched. To restore the operation, MUTE (Pin 15) needs to
be toggled to low and then to high again.
CLOCK LOSS DETECTION
The ADAU1592 includes a clock loss detection circuit. In case
the master clock to the part is lost, the ERR flag is set. This
condition is latched. To restore operation, MUTE needs to be
toggled low and high again.
AUTOMATIC RECOVERY FROM PROTECTIONS
In certain applications, it is desired for the amplifier to recover
itself from thermal protection without the need for system
microcontroller intervention.
The ADAU1592 thermal protection circuit issues two error
signals for this purpose: one a thermal warning (OTW) and the
other a thermal shutdown (ERR).
With the two error signals, there are two options available for
using the protections:
Option 1: Using OTW
Option 2: Using ERR
The following sections provide further details of these two options.
Option 1: Using OTW
The OTW pin is pulled low when the die temperature reaches
130°C to 135°C. This pin can be wired to MUTE as shown in
Figure 44, using an RC circuit.
06
74
9
-04
4
ADAU1592
OTW
TO MUTE
LOGIC INPUT
D1
1N4148
DVDD
R1
100k
10
15
MUTE
C1
47F
Figure 44. Option 1 Schematic for Autorecovery
The low logic level on OTW also pulls down the MUTE pin.
The bridge is shut down and starts cooling or the die tempera-
ture starts reducing. When it reaches around 120°C, the OTW
signal starts going high. While this pin is tied to a capacitor
with a resistor pulled to DVDD, the voltage on this pin starts
rising slowly towards DVDD. When it reaches the CMOS
threshold, MUTE is deasserted and the amplifier starts
functioning again. This cycle repeats itself depending on
the input signal conditions and the temperature of the die.
This option allows device operation that is safely below the
shutdown temperature of 150°C and allows the amplifier to
recover itself without the need for microcontroller intervention.
Option 2: Using ERR
Option 2 is similar to Option 1 except the ERR pin is tied to
MUTE instead of OTW. See the circuit in Figure 45.
06
74
9
-04
5
ADAU1592
ERR
TO MUTE
LOGIC INPUT
D1
1N4148
DVDD
R1
100k
MUTE
C1
47F
9
15
Figure 45. Option 2 Schematic for Autorecovery
In this case, the part goes into shutdown mode due to any of the
error-generating events like output overcurrent, overtemperature,
missing PVDD or DVDD, or clock loss. The part recovers itself
based on the same circuit operation in Figure 44.
However, if the part goes into error mode due to overtempera-
ture, then the device would have reached its maximum limit of
150°C (15°C to 20°C higher than Option 1). If it goes into error
mode due to an overcurrent from a short circuit on the speaker
outputs, then the part keeps itself recycling on and off until the
short circuit is removed.
It is possible that, with this operation, the part is subjected to a
much higher temperature and current stress continuously. This,
in turn, reduces the part’s reliability in the long term. Therefore,
using Option 1 for autorecovery from thermal protection and
using the system microcontroller to indicate to the user of an
error condition is recommended.
MUTE AND STDN
The MUTE and STDN pins are 3.3 V logic-compatible inputs
used to control the turn-on/turn-off for the ADAU1592.
The STDN input is active low when the STDN pin is pulled low
and the device is in its energy saving mode. The modulator is
inactive and the power stage is in high-Z state. The high logic
level input on the STDN pin wakes up the device. The modula-
tor is running internally but the power stage is still in high-Z state.
When the MUTE pin is pulled high, the power stage becomes
active with a soft turn-on to avoid the pop and clicks. The low
level on the MUTE pin disables the power stage and is
recommended to be used to mute the audio output. See the
Power-Up/Power-Down Sequence section for more details.
相關PDF資料 |
PDF描述 |
|---|---|
| ADAU1701JSTZ-RL | IC AUDIO PROC 2ADC/4DAC 48-LQFP |
| ADAU1702JSTZ-RL | IC AUDIO PROC 2ADC/4DAC 48-LQFP |
| ADAV4601BSTZ | IC AUDIO CODEC PROCESSOR 80-LQFP |
| ADAV4622BSTZ | IC AUD PRO ATV/SIF DECODE 80LQFP |
| ADCLK846BCPZ-REEL7 | IC CLK BUFFER 1:6 1.2GHZ 24LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADAU1592ACPZ-RL | 功能描述:IC AMP AUDIO PWR 24W 48LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:D 類 輸出類型:1-通道（單聲道），帶立體聲耳機 在某負載時最大輸出功率 x 通道數量:930mW x 1 @ 8 歐姆; 40mW x 2 @ 16 歐姆 電源電壓:2.7 V ~ 5.5 V 特點:消除爆音，差分輸入，I²C，靜音，關閉，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) 其它名稱:MAX97000EWA+T-ND |
| ADAU1592ACPZ-RL7 | 功能描述:IC AMP AUDIO PWR 48LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:D 類 輸出類型:1-通道（單聲道），帶立體聲耳機 在某負載時最大輸出功率 x 通道數量:930mW x 1 @ 8 歐姆; 40mW x 2 @ 16 歐姆 電源電壓:2.7 V ~ 5.5 V 特點:消除爆音，差分輸入，I²C，靜音，關閉，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) 其它名稱:MAX97000EWA+T-ND |
| ADAU1592ASVZ | 制造商:Analog Devices 功能描述:AMP AUDIO CLASS D SMD TQFPEP-48 |
| ADAU1592ASVZ-RL | 制造商:Analog Devices 功能描述: |
| ADAU1592ASVZ-RL7 | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。