- 您現在的位置：買賣IC網 > PDF目錄16928 > ADA4855-3YCP-EBZ (Analog Devices Inc)BOARD EVAL FOR ADA4855-3YCP PDF資料下載
參數資料
| 型號： | ADA4855-3YCP-EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 9/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR ADA4855-3YCP |
| 標準包裝： | 1 |
| 每 IC 通道數： | 3 - 三 |
| 放大器類型： | 電壓反饋 |
| 板類型： | 裸（未填充） |
| 已供物品： | 板 |
| 已用 IC / 零件： | 16-LFCSP 封裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
Data Sheet
ADA4855-3
Rev. A | Page 17 of 20
SINGLE-SUPPLY OPERATION
The ADA4855-3 is designed for a single power supply. Figure 54
shows the schematic for a single 5 V supply video driver. The
input signal is ac-coupled into the amplifier via C1. Resistor R2
and Resistor R4 establish the input midsupply reference for the
amplifier. C5 prevents constant current from being drawn
through the gain set resistor. C6 is the output coupling capacitor.
For more information on ac-coupled single-supply operation of
op amps, see Avoiding Op-Amp Instability Problems in Single-
Supply Applications, Analog Dialogue, Volume 35, Number 2,
March-May, 2001, at www.analog.com.
07
68
5-
15
5
C2
1F
R2
50k
R4
50k
R3
1k
C1
22F
U1
R1
75
R5
1k
R6
1k
C6
220F
R7
75
R8
75
C5
22F
ADA4855-3
5V
VOUT
VIN
–VS
C3
10F
C4
0.01F
5V
Figure 54. AC-Coupled, Single-Supply Video Driver Schematic
Another way to configure the ADA4855-3 in single-supply
operation is dc-coupled. The common-mode input voltage can
go ~200 mV below ground, which makes it a true single-supply
amplifier. However, in video applications, the black level is set at
0 V, which means that the output of the amplifier must go to
ground level as well. The ADA4855-3 has a rail-to-rail output
that can swing to within 100 mV from either rail. Figure 55
shows the schematic for adding 50 mV dc offset to the input
signal so that the output is not clipped while still properly
terminating the input with 75 Ω.
07
68
5-
15
6
R1
3.74k
U1
R2
76.8
R3
1k
R4
1k
R5
75
R6
75
ADA4855-3
5V
VOUT
VIN
–VS
C1
10F
C2
0.1F
5V
Figure 55. DC-Coupled, Single-Supply Video Driver Schematic
POWER SUPPLY BYPASSING
Careful attention must be paid to bypassing the power supply
pins of the ADA4855-3. High quality capacitors with low
equivalent series resistance (ESR), such as multilayer ceramic
capacitors (MLCCs), should be used to minimize supply voltage
ripple and power dissipation. A large, usually tantalum, 2.2 μF
to 47 μF capacitor located in close proximity to the ADA4855-3
is required to provide good decoupling for lower frequency
signals. The actual value is determined by the circuit transient
and frequency requirements. In addition, 0.1 μF MLCC decoupling
capacitors should be located as close to each of the power supply
pins and across both supplies as is physically possible, no more
than 1/8-inch away. The ground returns should terminate
immediately into the ground plane. Locating the bypass capacitor
return close to the load return minimizes ground loops and
improves performance.
LAYOUT
As is the case with all high speed applications, careful attention
to printed circuit board (PCB) layout details prevents associated
board parasitics from becoming problematic. The ADA4855-3
can operate at up to 410 MHz; therefore, proper RF design
techniques must be employed. The PCB should have a ground
plane covering all unused portions of the component side of the
board to provide a low impedance return path. Removing the
ground plane on all layers from the area near and under the
input and output pins reduces stray capacitance. Signal lines
connecting the feedback and gain resistors should be kept as short
as possible to minimize the inductance and stray capacitance
associated with these traces. Termination resistors and loads
should be located as close as possible to their respective inputs
and outputs. Input and output traces should be kept as far apart
as possible to minimize coupling (crosstalk) through the board.
Adherence to microstrip or stripline design techniques for long
signal traces (greater than 1 inch) is recommended. For more
information on high speed board layout, see A Practical Guide
to High-Speed Printed-Circuit-Board Layout, Analog Dialogue,
Volume 39, September 2005, at www.analog.com.
相關PDF資料 |
PDF描述 |
|---|---|
| NS10145T100MNA | INDUCTOR POWER 10UH 20% SMD |
| ADA4841-2YRM-EBZ | BOARD EVAL FOR ADA4841-2YRM |
| 0210490353 | CABLE JUMPER 1.25MM .152M 28POS |
| MIC2027-2BM TR | IC USB DISTRIB SW QUAD 16-SOIC |
| ADA4851-2YRM-EBZ | BOARD EVAL FOR ADA4851-2YRM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADA4855-3YCPZ-R2 | 制造商:Analog Devices 功能描述:OP Amp Triple Volt Fdbk R-R O/P 5.5V 16-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:OP AMP TRIPLE VOLT FDBK R-R O/P 5.5V 16LFCSP EP - Tape and Reel 制造商:Analog Devices 功能描述:IC OP-AMP 410MHZ 870V/ us LFCSP-16 制造商:Analog Devices 功能描述:IC, OP-AMP, 410MHZ, 870V/ us, LFCSP-16; Op Amp Type:High Speed; No. of Amplifiers:3; Slew Rate:870V/s; Supply Voltage Range:3V to 5.5V; Amplifier Case Style:LFCSP; No. of Pins:16; Bandwidth:410MHz; Operating Temperature Min:-40C ;RoHS Compliant: Yes |
| ADA4855-3YCPZ-R7 | 功能描述:IC OPAMP VF R-R TRPL LP 16LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
| ADA4855-3YCPZ-RL | 功能描述:IC OPAMP VF R-R TRPL LP 16LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
| ADA4856-3 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Single-Supply, High Speed, Fixed G = +2, Rail-to-Rail Output Video Amplifier |
| ADA4856-3YCP-EBZ | 功能描述:BOARD EVAL FOR ADA4856-3YCP RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
發布緊急采購，3分鐘左右您將得到回復。