- 您現在的位置：買賣IC網 > PDF目錄373972 > AD9985KSTZ-140 (ANALOG DEVICES INC) 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays PDF資料下載
參數資料
| 型號： | AD9985KSTZ-140 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 其它接口 |
| 英文描述： | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
| 中文描述： | SPECIALTY INTERFACE CIRCUIT, PQFP80 |
| 封裝： | LEAD FREE, MS-026BEC, LQFP-80 |
| 文件頁數： | 17/32頁 |
| 文件大小： | 349K |
| 代理商： | AD9985KSTZ-140 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD9985
Rev. 0 | Page 17 of 32
Hex
Address
03H
Write and
Read or
Read Only
R/W
Bits
7:3
Default
Value
01******
Register Name
Function
Bits [7:6] VCO Range. Selects VCO frequency range. (See PLL
description.)
Bits [5:3] Charge Pump Current. Varies the current that drives the
low-pass filter. (See PLL description.)
ADC Clock Phase Adjustment. Larger values mean more delay.
(1 LSB = T/32)
Places the clamp signal an integer number of clock periods after the
trailing edge of the Hsync signal.
Number of clock periods that the clamp signal is actively clamping.
Sets the number of pixel clocks that HSOUT will remain active.
**001***
04H
R/W
7:3
10000***
Phase Adjust
05H
R/W
7:0
10000000
Clamp
Placement
Clamp Duration
Hsync Output
Pulsewidth
Red Gain
Green Gain
Blue Gain
Red Offset
Green Offset
Blue Offset
Sync Control
06H
07H
08H
09H
0AH
0BH
0CH
0DH
0EH
R/W
R/W
7:0
7:0
10000000
00100000
R/W
R/W
R/W
R/W
R/W
R/W
R/W
7:0
7:0
7:0
7:1
7:1
7:1
7:0
10000000
10000000
10000000
1000000*
1000000*
1000000*
0*******
Controls ADC input range (contrast) of each respective channel.
Greater values give less contrast.
Controls dc offset (brightness) of each respective channel. Greater
values decrease brightness.
Bit 7 – Hsync Polarity Override. (Logic 0 = Polarity determined by chip,
Logic 1 = Polarity set by Bit 6 in Register 0EH.)
Bit 6 – Hsync Input Polarity. Indicates polarity of incoming Hsync signal
to the PLL. (Logic 0 = Active Low, Logic 1 = Active High.)
Bit 5 – Hsync Output Polarity. (Logic 0 = Logic High Sync, Logic 1 =
Logic Low Sync.)
Bit 4 – Active Hsync Override. If set to Logic 1, the user can select the
Hsync to be used via Bit 3. If set to Logic 0, the active interface is
selected via Bit 6 in Register 14H.
Bit 3 – Active Hsync Select. Logic 0 selects Hsync as the active sync.
Logic 1 selects Sync-on-Green as the active sync. Note that the
indicated Hsync will be used only if Bit 4 is set to Logic 1 or if both
syncs are active. (Bits 1, 7 = Logic 1 in Register 14H.)
Bit 2 – Vsync Output Invert. (Logic 1 = No Invert, Logic 0 = Invert.)
Bit 1 – Active Vsync Override. If set to Logic 1, the user can select the
Vsync to be used via Bit 0. If set to Logic 0, the active interface is
selected via Bit 3 in Register 14H.
Bit 0 – Active Vsync Select. Logic 0 selects raw Vsync as the output
Vsync. Logic 1 selects sync separated Vsync as the output Vsync. Note
that the indicated Vsync will be used only if Bit 1 is set to Logic 1.
Bit 7 – Clamp Function. Chooses between Hsync for Clamp signal or
another external signal to be used for clamping. (Logic 0 = Hsync,
Logic 1 = Clamp.)
Bit 6 – Clamp Polarity. Valid only with external Clamp signal. (Logic 0 =
Active High, Logic 1 Selects Active Low.)
Bit 5 – Coast Select. Logic 0 selects the coast input pins to be used for
the PLL coast. Logic 1 selects Vsync to be used for the PLL coast.
Bit 4 – Coast Polarity Override. (Logic 0 = Polarity determined by chip,
Logic 1 = Polarity set by Bit 3 in Register 0FH.)
Bit 3 – Coast Polarity. Selects polarity of external Coast signal. (Logic 0
= Active Low, Logic 1 = Active High.)
Bit 2 – Seek Mode Override. (Logic 1 = Allow Low Power Mode, Logic 0
= Disallow Low Power Mode.)
Bit 1 – PWRDN. Full Chip Power-Down, Active Low. (Logic 0 = Full Chip
Power-Down, Logic 1 = Normal.)
Sync-on-Green Threshold. Sets the voltage level of the Sync-on-Green
slicer’s comparator.
*1******
**0*****
***0****
****0***
*****0**
******0*
*******0
0FH
R/W
7:1
0*******
*1******
**0*****
***0****
****1***
*****1**
******1*
10H
R/W
7:3
10111***
Sync-on-Green
Threshold
相關PDF資料 |
PDF描述 |
|---|---|
| AD9990 | Dual Channel, 14-Bit CCD Signal Processor with V-Driver and Precision Timing |
| AD9991KCPRL | 10-Bit CCD Signal Processor with Precision Timing Generator |
| AD9991KCP | 10-Bit CCD Signal Processor with Precision Timing Generator |
| AD9991 | 10-Bit CCD Signal Processor with Precision Timing Generator |
| AD9992 | 12-Bit CCD Signal Processor with Precision Timing Generator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9990 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Channel, 14-Bit CCD Signal Processor with V-Driver and Precision Timing |
| AD9990BBCZ | 功能描述:IC CCD SGNL PROCESSOR 112CSPBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD9990BBCZRL | 功能描述:IC CCD SGNL PROCESSOR 112CSPBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD9991 | 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit CCD Signal Processor with Precision Timing Generator |
| AD9991KCP | 制造商:Analog Devices 功能描述:AFE Video 1ADC 10-Bit 3V 56-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。