- 您現在的位置：買賣IC網 > PDF目錄373972 > AD9954YSV-REEL7 (ANALOG DEVICES INC) 400 MSPS 14-Bit, 1.8 V CMOS Direct Digital Synthesizer PDF資料下載
參數資料
| 型號： | AD9954YSV-REEL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 數字信號處理外設 |
| 英文描述： | 400 MSPS 14-Bit, 1.8 V CMOS Direct Digital Synthesizer |
| 中文描述： | DSP-NUM CONTROLLED OSCILLATOR, PQFP48 |
| 封裝： | EXPOSED PAD, PLASTIC, MS-026-ABC, TQFP-48 |
| 文件頁數： | 18/36頁 |
| 文件大小： | 1027K |
| 代理商： | AD9954YSV-REEL7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
AD9954
Register
Name
(Serial
Address)
Positive
Linear
Sweep
Control
Word
(PLSCW)
(0x08)
Control Register Bit Descriptions
Control Function Register No.1 (CFR1)
Rev. 0 | Page 18 of 36
Bit Range
<7:0>
<15:8>
<23:16>
<31:24>
(MSB)
Bit 7
Bit 6
Bit 5
Rising Delta Frequency Tuning Word <7:0>
Rising Delta Frequency Tuning Word <15:8>
Rising Delta Frequency Tuning Word <23:16>
Rising Delta Frequency Tuning Word <31:24>
Bit 4
Bit 3
Bit 2
Bit 1
(LSB)
Bit 0
Default
Value
OR
Profile
PS0 = 1
PS0 = 1
PS0 = 1
PS0 = 1
PS0 = 1
<39:32>
Rising Sweep Ramp Rate Word <7:0>
The CFR1 is used to control the various functions, features,
and modes of the AD9954. The functionality of each bit is
detailed below.
CFR1<31>: RAM Enable Bit
CFR1<31> = 0 (default). When CFR1<31> is inactive, the RAM
is disabled for operation. Either single-tone mode of
operation or linear sweep mode of operation is enabled.
CFR1<31> = 1. If CFR1<31> is active, the RAM is
enabled for operation. Access control for normal operation is
controlled via the mode control bits of the RSCW for the cur-
rent profile.
CFR1<30>: RAM Destination Bit
CFR1<30> = 0 (default). If CFR1<31> is active, a Logic 0 on the
RAM destination bit (CFR1<30> = 0) configures the AD9954
such that the RAM output drives the phase accumulator (i.e.,
the frequency tuning word). If CFR1<31> is inactive,
CFR1<30> is a Don’t Care.
CFR1<30> = 1. If CFR1<31> is active, a Logic 1 on the RAM
destination bit (CFR1<30> = 1) configures the AD9954 such
that the RAM output drives the phase-offset adder (i.e., sets the
phase offset of the DDS core).
CFR1<29:27>: Internal Profile Control Bits
These bits cause the profile bits to be ignored when the RAM is
being used and puts the AD9954 into an automatic profile loop
sequence that allows the user to implement a frequency/phase
composite sweep that runs without external inputs. See the
Internal Profile Control section for more details.
CFR1<26>: Amplitude Ramp Rate Load Control Bit
CFR1<26> = 0 (default). The amplitude ramp rate timer is
loaded only upon timeout (timer == 1) and is not loaded due to
an I/O UPDATE input signal.
CFR1<26> = 1. The amplitude ramp rate timer is loaded upon
timeout (timer == 1) or at the time of an I/O UPDATE input signal.
CFR1<25>: Shaped On-Off Keying Enable Bit
CFR1<25> = 0 (default) Shaped on-off keying is
bypassed.
CFR1<25> = 1. Shaped on-off keying is enabled. When enabled,
CFR1<24> controls the mode of operation for this function.
CFR1<24>: Auto Shaped On-Off Keying Enable Bit (Only Valid
When CFR1<25> Is Active High)
CFR1<24> = 0 (default). When CFR1<25> is active, a Logic 0
on CFR1<24> enables the manual shaped on-off keying opera-
tion. Each amplitude sample sent to the DAC is multiplied by
the amplitude scale factor. See the Shaped On-Off Keying sec-
tion for details.
CFR1<24> = 1. When CFR1<25> is active, a Logic 1 on
CFR1<24> enables the auto shaped on-off keying operation.
Toggling the OSK pin high will cause the output scalar to ramp
up from zero scale to the amplitude scale factor at a rate deter-
mined by the amplitude ramp rate. Toggling the OSK pin low
will cause the output to ramp down from the amplitude scale
factor to zero scale at the amplitude ramp rate. See the Shaped
On-Off Keying section for details.
CFR1<23>: Automatic Synchronization Enable Bit
CFR1<23> = 0 (default). The automatic synchronization feature
of multiple AD9954s is inactive.
CFR1<23> = 1. The automatic synchronization feature of mul-
tiple AD9954s is active. The device will synchronize its internal
synchronization clock (SYNC_CLK) to align to the signal pre-
sent on the sync-in input. See the Synchronizing Multiple
AD9954s section for details.
CFR1<22>: Software Manual Synchronization of Multiple
AD9954
CFR1<22> = 0 (default). The manual synchronization feature is
inactive.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9956 | 2.7 GHz DDS-Based AgileRF |
| AD9956YCPZ-REEL1 | 2.7 GHz DDS-Based AgileRF |
| AD9956YCPZ1 | 2.7 GHz DDS-Based AgileRF |
| AD9957 | 1 GSPS Quadrature Digital Upconverter with 18-Bit IQ Data Path and 14-Bit DAC |
| AD9957BSVZ | 1 GSPS Quadrature Digital Upconverter with 18-Bit IQ Data Path and 14-Bit DAC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9954YSVZ | 功能描述:IC DDS DAC 14BIT 1.8V 48-TQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 直接數字合成 (DDS) 系列:- 產品變化通告:Product Discontinuance 27/Oct/2011 標準包裝:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 調節字寬（位）:32 b 電源電壓:2.97 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AD9954YSVZ | 制造商:Analog Devices 功能描述:IC DDS 400MSPS SMD 9954 TQFP48 |
| AD9954YSVZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:400 MSPS, 14-Bit, 1.8 V CMOS, Direct Digital Synthesizer |
| AD9954YSVZ-REEL7 | 功能描述:IC DDS DAC 14BIT 1.8V 48TQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 直接數字合成 (DDS) 系列:- 產品變化通告:Product Discontinuance 27/Oct/2011 標準包裝:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 調節字寬（位）:32 b 電源電壓:2.97 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AD9954YSVZ-REEL71 | 制造商:AD 制造商全稱:Analog Devices 功能描述:400 MSPS, 14-Bit, 1.8 V CMOS, Direct Digital Synthesizer |
發布緊急采購，3分鐘左右您將得到回復。