參數資料
型號： AD9948KCPZ
廠商： Analog Devices Inc
文件頁數： 28/28頁
文件大?。?/td> 0K
描述： IC CCD SIGNAL PROCESSOR 40-LFCSP
標準包裝： 1
類型： CCD 信號處理器，10 位
輸入類型： 邏輯
輸出類型： 邏輯
接口： 3 線串口
安裝類型： 表面貼裝
封裝/外殼： 40-VFQFN 裸露焊盤，CSP
供應商設備封裝： 40-LFCSP
包裝： 托盤
REV. 0
AD9948
–9–
SERIAL INTERFACE TIMING
All of the internal registers of the AD9948 are accessed through
a 3-wire serial interface. Each register consists of an 8-bit address
and a 24-bit data-word. Both the 8-bit address and 24-bit data-
word are written starting with the LSB. To write to each register,
a 32-bit operation is required, as shown in Figure 3a. Although
many registers are less than 24 bits wide, all 24 bits must be
written for each register. If the register is only 16 bits wide, then
the upper eight bits are don’t cares and may be filled with zeros
during the serial write operation. If fewer than 24 bits are written,
the register will not be updated with new data.
Figure 3b shows a more efficient way to write to the registers by
using the AD9948’s address auto-increment capability. Using
this method, the lowest desired address is written first, followed
by multiple 24-bit data-words. Each new 24-bit data-word will
be written automatically to the next highest register address. By
eliminating the need to write each 8-bit address, faster register
loading is achieved. Address auto-increment may be used start-
ing with any register location, and may be used to write to as
few as two registers or as many as the entire register space.
COMPLETE REGISTER LISTING
All addresses and default values are expressed in hexadecimal.
All registers are VD/HD updated as shown in Figure 3a, except
for the registers indicated in Table I, which are SL updated.
Table I. SL-Updated Registers
Register
Description
OPRMODE
AFE Operation Modes
CTLMODE
AFE Control Modes
SW_RESET
Software Reset Bit
TGCORE _RSTB
Reset Bar Signal for Internal TG Core
PREVENTUPDATE
Prevents Update of Registers
VDHDEDGE
VD/HD Active Edge
FIELDVAL
Resets Internal Field Pulse
HBLKRETIME
Retimes the HBLK to Internal Clock
CLPBLKOUT
CLP/BLK Output Pin Select
CLPBLKEN
Enables CLP/BLK Output Pin
H1CONTROL
H1/H2 Polarity Control
RGCONTROL
H1 Positive Edge Location
DRVCONTROL
H1 Negative Edge Location
SAMPCONTROL
H1 Drive Current
DOUTPHASE
H2 Drive Current
SDATA
A0
A1
A2
A4
A5
A6
A7
D0
D1
D2
D3
D21
D22
D23
SCK
SL
A3
NOTES
1. INDIVIDUAL SDATA BITS ARE LATCHED ON SCK RISING EDGES.
2. ALL 32 BITS MUST BE WRITTEN: 8 BITS FOR ADDRESS AND 24 BITS FOR DATA.
3. IF THE REGISTER LENGTH IS <24 BITS, THEN DON’T CARE BITS MUST BE USED TO COMPLETE THE 24-BIT DATA LENGTH.
4. NEW DATA IS UPDATED AT EITHER THE SL RISING EDGE OR AT THE HD FALLING EDGE AFTER THE NEXT VD FALLING EDGE.
5. VD/HD UPDATE POSITION MAY BE DELAYED TO ANY HD FALLING EDGE IN THE FIELD USING THE UPDATE REGISTER.
tDH
tLS
tLH
tDS
VD
SL UPDATED
VD/HD UPDATED
HD
...
8-BIT ADDRESS
24-BIT DATA
1
32
234
567
8
9
10
11
12
30
31
Figure 3a. Serial Write Operation
SDATA
A0
A1
A2
A4
A5
A6
A7
D0
D1
D22
D23
SCK
SL
A3
NOTES
1. MULTIPLE SEQUENTIAL REGISTERS MAY BE LOADED CONTINUOUSLY.
2. THE FIRST (LOWEST ADDRESS) REGISTER ADDRESS IS WRITTEN, FOLLOWED BY MULTIPLE 24-BIT DATA-WORDS.
3. THE ADDRESS WILL AUTOMATICALLY INCREMENT WITH EACH 24-BIT DATA-WORD (ALL 24 BITS MUST BE WRITTEN).
4. SL IS HELD LOW UNTIL THE LAST DESIRED REGISTER HAS BEEN LOADED.
5. NEW DATA IS UPDATED AT EITHER THE SL RISING EDGE OR AT THE HD FALLING EDGE AFTER THE NEXT VD FALLING EDGE.
D0
D1
D22
D23
D0
...
DATA FOR STARTING
REGISTER ADDRESS
DATA FOR NEXT
REGISTER ADDRESS
D2
D1
...
1
32
234
567
8
9
10
31
34
33
56
55
58
57
59
Figure 3b. Continuous Serial Write Operation
相關PDF資料
PDF描述
AD9949KCPZ IC CCD SIGNAL PROCESSOR 40-LFCSP
AD9951YSVZ IC DDS DAC 14BIT 1.8V 48-TQFP
AD9952YSVZ-REEL7 IC DDS DAC 14BIT 1.8V 48TQFP
AD9953YSVZ-REEL7 IC DDS DAC 14BIT 1.8V 48TQFP
AD9954YSVZ-REEL7 IC DDS DAC 14BIT 1.8V 48TQFP
相關代理商/技術參數
參數描述
AD9948KCPZRL 功能描述:IC CCD SIGNAL PROCESSOR 40-LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件
AD9949 制造商:AD 制造商全稱:Analog Devices 功能描述:12-Bit CCD Signal Processor with Precision Timing Core
AD9949AKCPZ 功能描述:IC CCD SIGNAL PROCESSOR 40-LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件
AD9949AKCPZRL 功能描述:IC CCD SIGNAL PROCESSOR 40-LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件
AD9949BCBZRL 制造商:Analog Devices 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*