- 您現在的位置：買賣IC網 > PDF目錄373966 > AD9760ARU (ANALOG DEVICES INC) 10-Bit, 125 MSPS TxDAC D/A Converter PDF資料下載
參數資料
| 型號： | AD9760ARU |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | DAC |
| 英文描述： | 10-Bit, 125 MSPS TxDAC D/A Converter |
| 中文描述： | PARALLEL, WORD INPUT LOADING, 0.035 us SETTLING TIME, 10-BIT DAC, PDSO28 |
| 封裝： | 0.170 INCH, TSSOP-28 |
| 文件頁數： | 16/23頁 |
| 文件大小： | 412K |
| 代理商： | AD9760ARU |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁
AD9760
–
16
–
REV. B
APPLYING THE AD9760
OUTPUT CONFIGURATIONS
The following sections illustrate some typical output configura-
tions for the AD9760. Unless otherwise noted, it is assumed
that I
OUTFS
is set to a nominal 20 mA. For applications requir-
ing the optimum dynamic performance, a differential output
configuration is suggested. A differential output configuration
may consist of either an RF transformer or a differential op amp
configuration. The transformer configuration provides the opti-
mum high frequency performance and is recommended for any
application allowing for ac coupling. The differential op amp
configuration is suitable for applications requiring dc coupling, a
bipolar output, signal gain and/or level shifting.
A single-ended output is suitable for applications requiring a
unipolar voltage output. A positive unipolar output voltage will
result if I
OUTA
and/or I
OUTB
is connected to an appropriately
sized load resistor, R
LOAD
, referred to ACOM. This configura-
tion may be more suitable for a single-supply system requiring
a dc coupled, ground referred output voltage. Alternatively, an
amplifier could be configured as an I-V converter, thus convert-
ing I
OUTA
or I
OUTB
into a negative unipolar voltage. This con-
figuration provides the best dc linearity since I
OUTA
or I
OUTB
is
maintained at a virtual ground. Note that I
OUTA
provides slightly
better performance than I
OUTB
.
DIFFERENTIAL COUPLING USING A TRANSFORMER
An RF transformer can be used to perform a differential-to-
single-ended signal conversion as shown in Figure 50. A
differentially coupled transformer output provides the optimum
distortion performance for output signals whose spectral content
lies within the transformer’s passband. An RF transformer such
as the Mini-Circuits T1-1T provides excellent rejection of com-
mon-mode distortion (i.e., even-order harmonics) and noise
over a wide frequency range. It also provides electrical isolation
and the ability to deliver twice the power to the load. Trans-
formers with different impedance ratios may also be used for
impedance matching purposes. Note that the transformer
provides ac coupling only.
R
LOAD
AD9760
22
21
MINI-CIRCUITS
T1-1T
OPTIONAL R
DIFF
I
OUTA
I
OUTB
Figure 50. Differential Output Using a Transformer
The center tap on the primary side of the transformer must be
connected to ACOM to provide the necessary dc current path
for both I
OUTA
and I
OUTB
. The complementary voltages appear-
ing at I
OUTA
and I
OUTB
(i.e., V
OUTA
and V
OUTB
) swing symmetri-
cally around ACOM and should be maintained with the specified
output compliance range of the AD9760. A differential resistor,
R
DIFF
, may be inserted in applications where the output of the
transformer is connected to the load, R
LOAD
, via a passive re-
construction filter or cable. R
DIFF
is determined by the
transformer’s impedance ratio and provides the proper source
termination that results in a low VSWR. Note that approxi-
mately half the signal power will be dissipated across R
DIFF
.
DIFFERENTIAL USING AN OP AMP
An op amp can also be used to perform a differential to single-
ended conversion as shown in Figure 51. The AD9760 is con-
figured with two equal load resistors, R
LOAD
, of 25
. The
differential voltage developed across I
OUTA
and I
OUTB
is con-
verted to a single-ended signal via the differential op amp con-
figuration. An optional capacitor can be installed across I
OUTA
and I
OUTB
, forming a real pole in a low-pass filter. The addition
of this capacitor also enhances the op amps distortion perfor-
mance by preventing the DACs high slewing output from over-
loading the op amp’s input.
AD9760
22
I
OUTA
I
OUTB
21
C
OPT
500
225
225
500
25
25
AD8047
Figure 51. DC Differential Coupling Using an Op Amp
The common-mode rejection of this configuration is typically
determined by the resistor matching. In this circuit, the differ-
ential op amp circuit using the AD8047 is configured to provide
some additional signal gain. The op amp must operate off of a
dual supply since its output is approximately
±
1.0 V. A high
speed amplifier capable of preserving the differential perfor-
mance of the AD9760 while meeting other system level objec-
tives (i.e., cost, power) should be selected. The op amps
differential gain, its gain setting resistor values, and full-scale
output swing capabilities should all be considered when opti-
mizing this circuit.
The differential circuit shown in Figure 52 provides the neces-
sary level-shifting required in a single supply system. In this
case, AVDD which is the positive analog supply for both the
AD9760 and the op amp is also used to level-shift the differ-
ential output of the AD9760 to midsupply (i.e., AVDD/2). The
AD8041 is a suitable op amp for this application.
AD9760
22
I
OUTA
I
OUTB
21
C
OPT
500
225
225
1k
25
25
AD8041
1k
AVDD
Figure 52. Single-Supply DC Differential Coupled Circuit
SINGLE-ENDED UNBUFFERED VOLTAGE OUTPUT
Figure 53 shows the AD9760 configured to provide a unipolar
output range of approximately 0 V to +0.5 V for a doubly termi-
nated 50
cable since the nominal full-scale current, I
OUTFS
, of
20 mA flows through the equivalent R
LOAD
of 25
. In this case,
R
LOAD
represents the equivalent load resistance seen by I
OUTA
or
I
OUTB
. The unused output (I
OUTA
or I
OUTB
) can be connected
to ACOM directly or via a matching R
LOAD
. Different values of
相關PDF資料 |
PDF描述 |
|---|---|
| AD9760* | Dual Synchronous 1.4A/800mA 4MHz Step-Down DC/DC Regulator; Package: DFN; No of Pins: 16; Temperature Range: -40°C to +125°C |
| AD9761-EB | Dual 10-Bit TxDAC+⑩ with 2x Interpolation Filters |
| AD9761ARS | Dual 10-Bit TxDAC+⑩ with 2x Interpolation Filters |
| AD9761 | Dual 10-Bit TxDAC with 23 Interpolation Filters(內插濾波器的雙10位D/A轉換器) |
| AD9762 | Analog Devices: Data Converters: DAC 12-Bit, 10 ns to 100 ns Converters Selection Table |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9760ARU50 | 功能描述:IC DAC 10BIT 50MSPS 28-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC® 標準包裝:47 系列:- 設置時間:2µs 位數:14 數據接口:并聯 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:55µW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:管件 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:* |
| AD9760ARU50RL | 功能描述:INTEGRATED CIRCUIT 制造商:analog devices inc. 系列:* 包裝:帶卷（TR） 零件狀態:最後搶購 封裝/外殼:28-TSSOP（0.173"，4.40mm 寬） 供應商器件封裝:28-TSSOP 標準包裝:1 |
| AD9760ARU50RL7 | 功能描述:IC DAC 10BIT 50MSPS 28-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC® 標準包裝:47 系列:- 設置時間:2µs 位數:14 數據接口:并聯 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:55µW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:管件 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:* |
| AD9760ARURL | 功能描述:INTEGRATED CIRCUIT 制造商:analog devices inc. 系列:* 包裝:帶卷（TR） 零件狀態:最後搶購 封裝/外殼:28-TSSOP（0.173"，4.40mm 寬） 供應商器件封裝:28-TSSOP 標準包裝:1 |
| AD9760ARURL7 | 制造商:Analog Devices 功能描述:DAC 1-CH 10-bit 28-Pin TSSOP T/R 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。