參數資料
型號： AD9754-EB
廠商： Analog Devices, Inc.
英文描述： 14-Bit, 125 MSPS High Performance TxDAC D/A Converter
中文描述： 14位，125 MSPS的TxDAC系列高性能D / A轉換
文件頁數： 9/24頁
文件大小： 327K
代理商： AD9754-EB
AD9754
–9–
REV. A
FUNCTIONAL DESCRIPTION
Figure 16 shows a simplified block diagram of the AD9754. The
AD9754 consists of a large PMOS current source array that is
capable of providing up to 20 mA of total current. The array
is divided into 31 equal currents that make up the five most
significant bits (MSBs). The next four bits or middle bits consist
of 15 equal current sources whose value is 1/16th of an MSB
current source. The remaining LSBs are binary weighted frac-
tions of the middle bits current sources. Implementing the
middle and lower bits with current sources, instead of an R-2R
ladder, enhances its dynamic performance for multitone or low
amplitude signals and helps maintain the DAC’s high output
impedance (i.e., >100 k
).
All of these current sources are switched to one or the other of
the two output nodes (i.e., IOUTA or IOUTB) via PMOS
differential current switches. The switches are based on a new
architecture that drastically improves distortion performance.
This new switch architecture reduces various timing errors and
provides matching complementary drive signals to the inputs of
the differential current switches.
The analog and digital sections of the AD9754 have separate
power supply inputs (i.e., AVDD and DVDD). The digital sec-
tion, which is capable of operating up to a 125 MSPS clock rate
and over +2.7 V to +5.5 V operating range, consists of edge-
triggered latches and segment decoding logic circuitry. The
analog section, which can operate over a +4.5 V to +5.5 V range
includes the PMOS current sources, the associated differential
switches, a 1.20 V bandgap voltage reference and a reference
control amplifier.
The full-scale output current is regulated by the reference con-
trol amplifier and can be set from 2 mA to 20 mA via an exter-
nal resistor, R
SET
. The external resistor, in combination with
both the reference control amplifier and voltage reference V
REFIO
,
sets the reference current I
REF
, which is mirrored over to the
segmented current sources with the proper scaling factor. The
full-scale current, I
OUTFS
, is 32 times the value of I
REF
.
DAC TRANSFER FUNCTION
The AD9754 provides complementary current outputs, IOUTA
and IOUTB. IOUTA will provide a near full-scale current out-
put, I
OUTFS
, when all bits are high (i.e., DAC CODE = 16383)
while IOUTB, the complementary output, provides no current.
The current output appearing at IOUTA and IOUTB is a func-
tion of both the input code and I
OUTFS
and can be expressed as:
IOUTA
= (
DAC CODE
/16384)
×
I
OUTFS
IOUTB
= (16383 –
DAC CODE
)/16384
×
I
OUTFS
where
DAC CODE
= 0 to 16383 (i.e., Decimal Representation).
As mentioned previously, I
OUTFS
is a function of the reference
current I
REF
, which is nominally set by a reference voltage V
REFIO
and external resistor R
SET
. It can be expressed as:
I
OUTFS
= 32
×
I
REF
where
I
REF
=
V
REFIO
/
R
SET
The two current outputs will typically drive a resistive load
directly or via a transformer. If dc coupling is required, IOUTA
and IOUTB should be directly connected to matching resistive
loads, R
LOAD
, that are tied to analog common, ACOM. Note
that R
LOAD
may represent the equivalent load resistance seen by
IOUTA or IOUTB as would be the case in a doubly terminated
50
or 75
cable. The single-ended voltage output appearing
at the IOUTA and IOUTB nodes is simply:
V
OUTA
=
IOUTA
×
R
LOAD
V
OUTB
=
IOUTB
×
R
LOAD
Note that the full-scale value of V
OUTA
and V
OUTB
should not
exceed the specified output compliance range to maintain speci-
fied distortion and linearity performance.
The differential voltage, V
DIFF
, appearing across IOUTA and
IOUTB is:
V
DIFF
= (
IOUTA – IOUTB
)
×
R
LOAD
Substituting the values of IOUTA, IOUTB and I
REF
; V
DIFF
can
be expressed as:
V
DIFF
= {(2
DAC CODE
– 16383)/16384}
×
V
DIFF
= {
(32
R
LOAD
/
R
SET
)
×
V
REFIO
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
DIGITAL DATA INPUTS (DB13–DB0)
150pF
+1.20V REF
AVDD
ACOM
REFLO
ICOMP
PMOS
CURRENT SOURCE
ARRAY
+5V
SEGMENTED SWITCHES
FOR DB13–DB5
LSB
SWITCHES
REFIO
FS ADJ
DVDD
DCOM
CLOCK
+5V
R
SET
2k
V
0.1
m
F
IOUTA
IOUTB
0.1
m
F
AD9754
SLEEP
LATCHES
I
REF
V
REFIO
CLOCK
I
OUTB
I
OUTA
R
LOAD
50
V
V
OUTB
V
OUTA
R
LOAD
50
V
V
DIFF
= V
OUTA
– V
OUTB
Figure 16. Functional Block Diagram
相關PDF資料
PDF描述
AD9754AR 14-Bit, 125 MSPS High Performance TxDAC D/A Converter
AD9760ARU50 10-Bit, 125 MSPS TxDAC D/A Converter
AD9760 10-Bit, 125 MSPS TxDAC D/A Converter
AD9760-EB 10-Bit, 125 MSPS TxDAC D/A Converter
AD9760AR 10-Bit, 125 MSPS TxDAC D/A Converter
相關代理商/技術參數
參數描述
AD9754-EBZ 功能描述:BOARD EVAL FOR AD9754 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:TxDAC® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
AD9755 制造商:未知廠家 制造商全稱:未知廠家 功能描述:AD9755: 14-Bit. 300 MSPS High-Speed TxDAC+?D/A Converter Data Sheet (Rev. A. 1/03)
AD9755AST 制造商:Analog Devices 功能描述:DAC 1-CH Segment 14-bit 48-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:14-BIT, 300 MSPS TXDAC+ D/A CONVERTER - Bulk 制造商:Analog Devices 功能描述:CONVERTOR DA ((NW))
AD9755-AST 制造商:Analog Devices 功能描述:
AD9755ASTRL 制造商:Analog Devices 功能描述:DAC 1-CH Segment 14-bit 48-Pin LQFP T/R 制造商:Rochester Electronics LLC 功能描述:14-BIT, 300 MSPS TXDAC+ D/A CONVERTER - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*