- 您現在的位置：買賣IC網 > PDF目錄373966 > AD9750AR (ANALOG DEVICES INC) 10-Bit, 125 MSPS High Performance TxDAC D/A Converter PDF資料下載
參數資料
| 型號： | AD9750AR |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | DAC |
| 英文描述： | 10-Bit, 125 MSPS High Performance TxDAC D/A Converter |
| 中文描述： | PARALLEL, WORD INPUT LOADING, 0.035 us SETTLING TIME, 10-BIT DAC, PDSO28 |
| 封裝： | 0.300 INCH, SOIC-28 |
| 文件頁數： | 10/22頁 |
| 文件大?。?/td> | 302K |
| 代理商： | AD9750AR |
AD9750
–10–
REV. 0
REFERENCE OPERATION
The AD9750 contains an internal 1.20 V bandgap reference
that can easily be disabled and overridden by an external refer-
ence. REFIO serves as either an
input
or
output
depending on
whether the internal or an external reference is selected. If
REFLO is tied to ACOM, as shown in Figure 18, the internal
reference is activated and REFIO provides a 1.20 V output. In
this case, the internal reference
must
be compensated externally
with a ceramic chip capacitor of 0.1
μ
F or greater from REFIO
to REFLO. Also, REFIO should be buffered with an external
amplifier having an input bias current less than 100 nA if any
additional loading is required.
150pF
+1.2V REF
AVDD
REFLO
CURRENT
SOURCE
ARRAY
+5V
REFIO
FS ADJ
2k
V
0.1
m
F
AD9750
ADDITIONAL
LOAD
OPTIONAL
EXTERNAL
REF BUFFER
Figure 18. Internal Reference Configuration
The internal reference can be disabled by connecting REFLO to
AVDD. In this case, an external reference may then be applied
to REFIO as shown in Figure 19. The external reference may
provide either a fixed reference voltage to enhance accuracy and
drift performance or a varying reference voltage for gain control.
Note that the 0.1
μ
F compensation capacitor is not required
since the internal reference is disabled, and the high input im-
pedance (i.e., 1 M
) of REFIO minimizes any loading of the
external reference.
150pF
+1.2V REF
AVDD
REFLO
CURRENT
SOURCE
ARRAY
AVDD
REFIO
FS ADJ
R
SET
AD9750
EXTERNAL
REF
I
REF
=
V
REFIO
/R
SET
AVDD
REFERENCE
CONTROL
AMPLIFIER
V
REFIO
Figure 19. External Reference Configuration
REFERENCE CONTROL AMPLIFIER
The AD9750 also contains an internal control amplifier that is
used to regulate the DAC’s full-scale output current, I
OUTFS
.
The control amplifier is configured as a V-I converter as shown
in Figure 19, such that its current output, I
REF
, is determined by
the ratio of the V
REFIO
and an external resistor, R
SET
, as stated
in Equation 4. I
REF
is copied over to the segmented current
sources with the proper scaling factor to set I
OUTFS
as stated in
Equation 3.
The control amplifier allows a wide (10:1) adjustment span of
I
OUTFS
over a 2 mA to 20 mA range by setting IREF between
62.5
μ
A and 625
μ
A. The wide adjustment span of I
OUTFS
provides several application benefits. The first benefit relates
directly to the power dissipation of the AD9750, which is
proportional to I
OUTFS
(refer to the Power Dissipation section).
The second benefit relates to the 20 dB adjustment, which is
useful for system gain control purposes.
The small signal bandwidth of the reference control amplifier is
approximately 0.5 MHz. The output of the control amplifier is
internally compensated via a 150 pF capacitor that limits the
control amplifier small-signal bandwidth and reduces its
output impedance. Since the –3 dB bandwidth corresponds to
the dominant pole, and hence the time constant, the settling
time of the control amplifier to a stepped reference input re-
sponse can be approximated. In this case, the time constant can
be approximated to be 320 ns.
There are two methods in which I
REF
can be varied for a fixed
R
SET
. The first method is suitable for a single-supply system in
which the internal reference is disabled, and the common-mode
voltage of REFIO is varied over its compliance range of 1.25 V
to 0.10 V. REFIO can be driven by a single-supply amplifier or
DAC, thus allowing I
REF
to be varied for a fixed R
SET
. Since the
input impedance of REFIO is approximately 1 M
, a simple,
low cost R-2R ladder DAC configured in the voltage mode
topology may be used to control the gain. This circuit is shown
in Figure 20 using the AD7524 and an external 1.2 V reference,
the AD1580.
The second method may be used in a dual-supply system in
which the common-mode voltage of REFIO is fixed and I
REF
is
varied by an external voltage, V
GC
, applied to R
SET
via an ampli-
fier. An example of this method is shown in Figure 21, in which
the internal reference is used to set the common-mode voltage
of the control amplifier to 1.20 V. The external voltage, V
GC
, is
referenced to ACOM and should not exceed 1.2 V. The value of
R
SET
is such that I
REFMAX
and I
REFMIN
do not exceed 62.5
μ
A
1.2V
150pF
+1.2V REF
AVDD
REFLO
CURRENT
SOURCE
ARRAY
AVDD
REFIO
FS ADJ
R
SET
AD9750
I
REF
=
V
REF
/R
SET
AVDD
V
REF
V
DD
R
FB
OUT1
OUT2
AGND
DB7–DB0
AD7524
AD1580
0.1V TO 1.2V
Figure 20. Single-Supply Gain Control Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| AD9750ARU | 10-Bit, 125 MSPS High Performance TxDAC D/A Converter |
| AD9750 | 10-Bit D/A Converter(100MSPS,10位D/A轉換器) |
| AD9752* | 12-Bit. 125 MSPS High Performance TxDAC D/A Converter |
| AD9752-EB | 12-Bit, 125 MSPS High Performance TxDAC D/A Converter |
| AD9752AR | 12-Bit, 125 MSPS High Performance TxDAC D/A Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9750ARRL | 制造商:Analog Devices 功能描述:DAC 1-CH Segment 10-bit 28-Pin SOIC W T/R 制造商:Rochester Electronics LLC 功能描述:10 BIT 125 MSPS+ TXDAC D/A CONVERTER - Bulk |
| AD9750ARU | 制造商:Analog Devices 功能描述:DAC 1-CH Segment 10-bit 28-Pin TSSOP 制造商:Rochester Electronics LLC 功能描述:10 BIT 125 MSPS+ TXDAC D/A CONVERTER - Bulk |
| AD9750ARURL7 | 制造商:Analog Devices 功能描述:DAC 1-CH Segment 10-bit 28-Pin TSSOP T/R 制造商:Rochester Electronics LLC 功能描述:10 BIT 125 MSPS+ TXDAC D/A CONVERTER - Bulk |
| AD9750ARUZ | 功能描述:IC DAC 10BIT 125MSPS 28TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC® 標準包裝:1 系列:- 設置時間:4.5µs 位數:12 數據接口:串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOICN 包裝:剪切帶 (CT) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:* 其它名稱:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
| AD9750ARUZRL7 | 功能描述:IC DAC 10BIT 125MSPS 28TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC® 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:8 電壓電源:單電源 功率耗散（最大）:2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP（4x3） 包裝:管件 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
發布緊急采購，3分鐘左右您將得到回復。